PIC18F6410-I/PT Microchip Technology, PIC18F6410-I/PT Datasheet - Page 168

• Manufacturer Part Number: PIC18F6410-I/PT
• Description: IC PIC MCU FLASH 8KX16 64TQFP
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F6410-I/PT

• Program Memory Type: FLASH
• Program Memory Size: 16KB (8K x 16)
• Package / Case: 64-TFQFP
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 54
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SPI/I2C/EUSART/AUSART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 4
• Operating Supply Voltage: 4.2 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, ICE2000, ICE4000, DV164136, DM183032
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 10-bit
• Package: 64TQFP
• Device Core: PIC
• Family Name: PIC18
• Maximum Speed: 40 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT64PT5 - SOCKET TRAN ICE 64MQFP/TQFPAC164319 - MODULE SKT MPLAB PM3 64TQFPDV007003 - PROGRAMMER UNIVERSAL PROMATE II
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC18F6310/6410/8310/8410
16.1
Each Capture/Compare/PWM module is associated
with a control register (generically, CCPxCON) and a
data register (CCPRx). The data register, in turn, is
comprised of two 8-bit registers: CCPRxL (low byte)
and CCPRxH (high byte). All registers are both
readable and writable.
16.1.1
The CCP modules utilize Timers 1, 2 or 3, depending
on the mode selected. Timer1 and Timer3 are available
to modules in Capture or Compare modes, while
Timer2 is available for modules in PWM mode.
TABLE 16-1:
The assignment of a particular timer to a module is
determined by the Timer-to-CCP enable bits in the
T3CON register
be active at any given time and may share the same
FIGURE 16-1:
DS39635C-page 168
Timer1 is used for all
Capture and Compare
operations for all three
CCP modules. Timer2
is used for PWM oper-
ations for all three CCP
modules. Timer3 is not
used.
All modules may share
Timer1
resources as common
time bases.
TMR1
TMR2
CCP1
CCP2
CCP3
T3CCP<2:1> = 00
CCP Mode
Compare
Capture
CCP Module Configuration
and
PWM
CCP MODULES AND TIMER
RESOURCES
Timer2
(Register
CCP MODE – TIMER
RESOURCE
TMR3
CCP AND TIMER INTERCONNECT CONFIGURATIONS
15-1). All three modules may
Timer1 or Timer3
Timer1 or Timer3
Timer Resource
Timer1 is used for
Capture and Compare
operations for CCP1
and Timer 3 is used for
CCP2 and CCP3.
All
share Timer2 as a
common time base for
PWM operation.
TMR1
CCP1
T3CCP<2:1> = 01
Timer2
three
TMR2
modules
TMR3
CCP2
CCP3
Timer1 is used for
Capture and Compare
operations for CCP1
and CCP2. Timer 3 is
used for CCP3.
All
share Timer2 as a
common time base for
PWM operation.
timer resource if they are configured to operate in the
same mode (Capture/Compare or PWM) at the same
time.
Depending on the configuration selected, up to three
timers may be active at once, with modules in the same
configuration (Capture/Compare or PWM) sharing
timer resources. The possible configurations are
shown in
16.1.2
The CCP2MX Configuration bit determines if CCP2 is
multiplexed to its default or alternate assignment. By
default, CCP2 is assigned to RC1 (CCP2MX = 1). If
CCP2MX is cleared, CCP2 is multiplexed with either
RE7 or RB3 (RE7 is the only alternative assignment for
64-pin devices).
For any device in Microcontroller mode, the alternate
CCP2 assignment is RE7. For 80-pin devices in
Microcprocessor, Extended Microcontroller or Microcon-
troller with Boot Block mode, the alternate assignment is
RB3. Note that RE7 is the only alternative assignment for
64-pin devices.
Changing the pin assignment of CCP2 does not auto-
matically change any requirements for configuring the
port pin. Users must always verify that the appropriate
TRIS register is configured correctly for CCP2
operation, regardless of where it is located.
TMR1
CCP1
CCP2
T3CCP<2:1> = 10
three
TMR2
Figure
CCP2 PIN ASSIGNMENT
modules
TMR3
CCP3
16-1.
 2010 Microchip Technology Inc.
TMR1
T3CCP<2:1> = 11
Timer3 is used for all
Capture and Compare
operations for all three
CCP modules. Timer2
is used for PWM oper-
ations for all three CCP
modules. Timer1 is not
used.
All modules may share
Timer2
resources as common
time bases.
and
TMR3
TMR2
CCP1
CCP2
CCP3
Timer3