DSPIC30F3010-30I/ML Microchip Technology, DSPIC30F3010-30I/ML Datasheet - Page 132

• Manufacturer Part Number: DSPIC30F3010-30I/ML
• Description: IC DSPIC MCU/DSP 24K 44QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F3010-30I/ML

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 24KB (8K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Package: 44QFN EP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Interface Type: I2C/SPI/UART
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 5
• For Use With: XLT44QFN4 - SOCKET TRANS ICE 28DIP TO 44QFNXLT28QFN4 - SOCKET TRANS ICE 28QFN W/CABLEAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DSPIC30F301030IML

dsPIC30F3010/3011
The configuration guidelines give the required setup
values for the conversion speeds above 500 ksps,
since they require external V
are some differences in the configuration procedure.
Configuration details that are not critical to the
conversion speed have been omitted.
Figure 19-2
conversion rates above 500 ksps.
FIGURE 19-2:
19.7.1
The configuration for 1 Msps operation is dependent on
whether a single input pin is to be sampled or whether
multiple pins will be sampled.
19.7.1.1
For conversions at 1 Msps for a single analog input, at
least two sample and hold channels must be enabled.
The analog input multiplexer must be configured so
that the same input pin is connected to both sample
and hold channels. The ADC converts the value held
on one S/H channel, while the second S/H channel
acquires a new input sample.
DS70141F-page 132
1 Msps CONFIGURATION
GUIDELINE
depicts the recommended circuit for the
Single Analog Input
V
DD
ADC VOLTAGE REFERENCE SCHEMATIC
REF
10
11
1
2
3
4
5
6
7
8
9
pins usage and there
V
V
SS
DD
dsPIC30F3011
V
DD
10
R1
0.1 μF
V
V
DD
SS
C2
33
32
31
30
29
28
27
26
25
24
23
V
DD
19.7.1.2
The ADC can also be used to sample multiple analog
inputs using multiple sample and hold channels. In this
case, the total 1 Msps conversion rate is divided among
the different input signals. For example, four inputs can
be sampled at a rate of 250 ksps for each signal or two
inputs could be sampled at a rate of 500 ksps for each
signal. Sequential sampling must be used in this
configuration to allow adequate sampling time on each
input.
R2
10
C1
0.01 μF
V
DD
Multiple Analog Inputs
C8
1 μF
C5
1 μF
V
V
DD
DD
© 2010 Microchip Technology Inc.
0.1 μF
0.1 μF
C7
C4
V
V
DD
DD
0.01 μF
0.01 μF
C6
C3
V
V
DD
DD