DSPIC30F3010-30I/ML Microchip Technology, DSPIC30F3010-30I/ML Datasheet - Page 143

• Manufacturer Part Number: DSPIC30F3010-30I/ML
• Description: IC DSPIC MCU/DSP 24K 44QFN
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F3010-30I/ML

• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 30 MIPs
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, Motor Control PWM, QEI, POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 24KB (8K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 6x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Package: 44QFN EP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 30 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Interface Type: I2C/SPI/UART
• On-chip Adc: 6-chx10-bit
• Number Of Timers: 5
• For Use With: XLT44QFN4 - SOCKET TRANS ICE 28DIP TO 44QFNXLT28QFN4 - SOCKET TRANS ICE 28QFN W/CABLEAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DSPIC30F301030IML

20.2.3
Enabling the LP oscillator is controlled with two
elements:
• The current oscillator group bits, COSC<2:0>
• The LPOSCEN bit (OSCON register)
The LP oscillator is on (even during Sleep mode) if
LPOSCEN = 1. The LP oscillator is the device clock if:
• COSC<1:0> = 00 (LP selected as main osc.) and
• LPOSCEN = 1
Keeping the LP oscillator on at all times allows for a
fast switch to the 32 kHz system clock for lower power
operation. Returning to the faster main oscillator will
still require a start-up time.
20.2.4
The PLL multiplies the clock which is generated by the
primary oscillator. The PLL is selectable to have either
gains of x4, x8 and x16. Input and output frequency
ranges are summarized in
TABLE 20-3:
The PLL features a lock output, which is asserted when
the PLL enters a phase locked state. Should the loop
fall out of lock (e.g., due to noise), the lock signal will be
rescinded. The state of this signal is reflected in the
read-only LOCK bit in the OSCCON register.
20.2.5
The FRC oscillator is a fast (7.37 MHz +/- 2% nominal)
internal RC oscillator. This oscillator is intended to pro-
vide reasonable device operating speeds without the
use of an external crystal, ceramic resonator or RC net-
work. The FRC oscillator can be used with the PLL to
obtain higher clock frequencies.
The dsPIC30F operates from the FRC oscillator
whenever the current oscillator selection control bits in
the OSCCON register (OSCCON<13:12>) are set to
‘01’.
The
(OSCTUN<3:0>) allows the user to tune the internal
fast RC oscillator (nominal 7.37 MHz). The user can
tune the FRC oscillator within a range of +10.5%
© 2010 Microchip Technology Inc.
4 MHz-10 MHz
4 MHz-10 MHz
4 MHz-7.5 MHz
four-bit
F
IN
LP OSCILLATOR CONTROL
PHASE LOCKED LOOP (PLL)
FAST RC OSCILLATOR (FRC)
field
PLL FREQUENCY RANGE
Multiplier
PLL
x16
specified
x4
x8
Table
20-3.
16 MHz-40 MHz
32 MHz-80 MHz
64 MHz-120 MHz
by
F
OUT
TUN<3:0>
(840 kHz) and -12% (960 kHz) in steps of 1.50%
around the factory calibrated setting, as shown in
Table
If OSCCON<14:12> are set to ‘111’ and FPR<4:0> are
set to ‘00101’, ‘00110’ or ‘00111’, then a PLL
multiplier of 4, 8 or 16 (respectively) is applied
.
TABLE 20-4:
20.2.6
The LPRC oscillator is a component of the Watchdog
Timer (WDT) and oscillates at a nominal frequency of
512 kHz. The LPRC oscillator is the clock source for
the Power-up Timer (PWRT) circuit, WDT and clock
monitor circuits. It may also be used to provide a low-
frequency clock source option for applications where
power consumption is critical and timing accuracy is
not required.
The LPRC oscillator is always enabled at a Power-on
Reset, because it is the clock source for the PWRT.
After the PWRT expires, the LPRC oscillator will remain
ON if one of the following is true:
• The Fail-Safe Clock Monitor is enabled
• The WDT is enabled
• The LPRC oscillator is selected as the system
Note:
Note:
clock via the COSC<1:0> control bits in the
OSCCON register
TUN<3:0>
dsPIC30F3010/3011
0111
0110
0101
0100
0011
0010
0001
0000
1111
1110
1101
1100
1011
1010
1001
1000
Bits
20-4.
OSCTUN functionality has been provided
to
temperature effects on the FRC frequency
over a wide range of temperatures. The
tuning step size is an approximation and is
neither characterized nor tested.
When a 16x PLL is used, the FRC
frequency must not be tuned to a
frequency greater than 7.5 MHz.
LOW-POWER RC OSCILLATOR (LPRC)
help
Center Frequency (oscillator is
running at calibrated frequency)
FRC TUNING
customers
FRC Frequency
+10.5%
+9.0%
+7.5%
+6.0%
+4.5%
+3.0%
+1.5%
-1.5%
-3.0%
-4.5%
-6.0%
-7.5%
-9.0%
-10.5%
-12.0%
DS70141F-page 143
compensate
for