PIC24HJ64GP502-E/MM Microchip Technology, PIC24HJ64GP502-E/MM Datasheet - Page 134

• Manufacturer Part Number: PIC24HJ64GP502-E/MM
• Description: IC PIC MCU FLASH 64K 28-QFN
• Manufacturer: Microchip Technology
• Series: PIC® 24Hr

Specifications of PIC24HJ64GP502-E/MM

• Program Memory Type: FLASH
• Program Memory Size: 64KB (22K x 24)
• Package / Case: 28-QFN
• Core Processor: PIC
• Core Size: 16-Bit
• Speed: 40 MIPs
• Connectivity: CAN, I²C, IrDA, LIN, PMP, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 21
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 3.6 V
• Data Converters: A/D 10x10b/12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Processor Series: PIC24HJ
• Core: PIC
• Data Bus Width: 16 bit
• Data Ram Size: 8 KB
• Interface Type: I2C/SPI/UART
• Maximum Clock Frequency: 40 MHz
• Number Of Programmable I/os: 21
• Number Of Timers: 5
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: 52713-733, 52714-737, 53276-922, EWDSPIC
• Development Tools By Supplier: PG164130, DV164035, DV244005, DV164005, PG164120, DM300027
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10-ch x 10-bit or 10-ch x 12-bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: AC164336 - MODULE SOCKET FOR PM3 28/44QFN
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

PIC24HJ32GP302/304, PIC24HJ64GPX02/X04 AND PIC24HJ128GPX02/X04
11.2
In addition to the PORT, LAT and TRIS registers for
data control, some port pins can also be individually
configured for either digital or open-drain output. This
is controlled by the Open-Drain Control register,
ODCx, associated with each port. Setting any of the
bits configures the corresponding pin to act as an
open-drain output.
The open-drain feature allows the generation of
outputs higher than V
tolerant pins by using external pull-up resistors. The
maximum open-drain voltage allowed is the same as
the maximum V
See
functionality.
11.3
The AD1PCFGL and TRIS registers control the opera-
tion of the analog-to-digital (A/D) port pins. The port
pins that are to function as analog inputs must have
their corresponding TRIS bit set (input). If the TRIS bit
is cleared (output), the digital output level (V
is converted.
The AD1PCFGL register has a default value of 0x0000;
therefore, all pins that share ANx functions are analog
(not digital) by default.
When the PORT register is read, all pins configured as
analog input channels are read as cleared (a low level).
Pins configured as digital inputs do not convert an
analog input. Analog levels on any pin defined as a
digital input (including the ANx pins) can cause the
input buffer to consume current that exceeds the
device specifications.
EXAMPLE 11-1:
DS70293E-page 134
MOV
MOV
NOP
btss
“Pin
0xFF00, W0
W0, TRISBB
PORTB, #13
Open-Drain Configuration
Configuring Analog Port Pins
Diagrams” for the available pins and their
IH
specification.
DD
PORT WRITE/READ EXAMPLE
(e.g., 5V) on any desired 5V
; Configure PORTB<15:8> as inputs
; and PORTB<7:0> as outputs
; Delay 1 cycle
; Next Instruction
OH
or V
OL
)
11.4
One instruction cycle is required between a port
direction change or port write operation and a read
operation of the same port. Typically this instruction
would be an NOP, as shown in
11.5
The input change notification function of the I/O ports
allows the PIC24HJ32GP302/304, PIC24HJ64GPX02/
X04 and PIC24HJ128GPX02/X04 devices to generate
interrupt requests to the processor in response to a
change-of-state on selected input pins. This feature
can detect input change-of-states even in Sleep mode,
when the clocks are disabled. Depending on the device
pin count, up to 21 external signals (CNx pin) can be
selected (enabled) for generating an interrupt request
on a change-of-state.
Four control registers are associated with the CN mod-
ule. The CNEN1 and CNEN2 registers contain the
interrupt enable control bits for each of the CN input
pins. Setting any of these bits enables a CN interrupt
for the corresponding pins.
Each CN pin also has a weak pull-up connected to it.
The pull-ups act as a current source connected to the
pin, and eliminate the need for external resistors when
push-button or keypad devices are connected. The
pull-ups are enabled separately using the CNPU1 and
CNPU2 registers, which contain the control bits for
each of the CN pins. Setting any of the control bits
enables the weak pull-ups for the corresponding pins.
Note:
I/O Port Write/Read Timing
Input Change Notification
Pull-ups on change notification pins
should always be disabled when the port
pin is configured as a digital output.
© 2011 Microchip Technology Inc.
Example
11-1.