ATMEGA169P-16AU Atmel, ATMEGA169P-16AU Datasheet - Page 299

• Manufacturer Part Number: ATMEGA169P-16AU
• Description: IC AVR MCU 16K 16MHZ IND 64-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA169P-16AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: ATMEGA16x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI/USART/USI
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRBFLY
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Package: 64TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• For Use With: ATSTK600-TQFP64 - STK600 SOCKET/ADAPTER 64-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATAVRBFLY - KIT EVALUATION AVR BUTTERFLYATSTK502 - MOD EXPANSION AVR STARTER 500ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

27.2.1
27.3
27.4
27.5
27.6
27.6.1
8018P–AVR–08/10
Signature Bytes
Calibration Byte
Page Size
Parallel Programming Parameters, Pin Mapping, and Commands
Latching of Fuses
Signal Names
The fuse values are latched when the device enters programming mode and changes of the
fuse values will have no effect until the part leaves Programming mode. This does not apply to
the EESAVE Fuse which will take effect once it is programmed. The fuses are also latched on
Power-up in Normal mode.
All Atmel microcontrollers have a three-byte signature code which identifies the device. This
code can be read in both serial and parallel mode, also when the device is locked. The three
bytes reside in a separate address space. The signature bytes are given in
Table 27-6.
The ATmega169P has a byte calibration value for the internal RC Oscillator. This byte resides in
the high byte of address 0x000 in the signature address space. During reset, this byte is auto-
matically written into the OSCCAL Register to ensure correct frequency of the calibrated RC
Oscillator.
Table 27-7.
Table 27-8.
This section describes how to parallel program and verify Flash Program memory, EEPROM
Data memory, Memory Lock bits, and Fuse bits in the ATmega169P. Pulses are assumed to be
at least 250 ns unless otherwise noted.
In this section, some pins of the ATmega169P are referenced by signal names describing their
functionality during parallel programming, see
300. Pins not described in
The XA1/XA0 pins determine the action executed when the XTAL1 pin is given a positive pulse.
The bit coding is shown in
Part
ATmega169P
8K words (16 Kbytes)
EEPROM Size
Flash Size
512 bytes
Device and JTAG ID
No. of Words in a Page and No. of Pages in the Flash
No. of Words in a Page and No. of Pages in the EEPROM
0x000
0x1E
Signature Bytes Address
Table 27-9 on page 300
Table 27-11 on page
Page Size
Page Size
64 words
4 bytes
0x001
0x94
PCWORD
PCWORD
EEA[1:0]
PC[5:0]
0x002
Figure 27-1 on page 300
0x05
301.
are referenced by pin names.
No. of Pages
No. of Pages
Part Number
128
128
9405
ATmega169P
and
JTAG
PCPAGE
EEA[8:2]
PCPAGE
PC[12:6]
Table
Table 27-9 on page
Manufacture ID
27-6.
0x1F
EEAMSB
PCMSB
12
8
299