ATMEGA169P-16AU Atmel, ATMEGA169P-16AU Datasheet - Page 305

• Manufacturer Part Number: ATMEGA169P-16AU
• Description: IC AVR MCU 16K 16MHZ IND 64-TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA169P-16AU

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 16MHz
• Connectivity: SPI, UART/USART, USI
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 54
• Program Memory Size: 16KB (8K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 512 x 8
• Ram Size: 1K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP, 64-VQFP
• Processor Series: ATMEGA16x
• Core: AVR8
• Data Bus Width: 8 bit
• Data Ram Size: 1 KB
• Interface Type: SPI/USART/USI
• Maximum Clock Frequency: 16 MHz
• Number Of Programmable I/os: 54
• Number Of Timers: 3
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWAVR, EWAVR-BL
• Development Tools By Supplier: ATAVRDRAGON, ATSTK500, ATSTK600, ATAVRISP2, ATAVRONEKIT, ATAVRBFLY
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Package: 64TQFP
• Device Core: AVR
• Family Name: ATmega
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 3.3|5 V
• For Use With: ATSTK600-TQFP64 - STK600 SOCKET/ADAPTER 64-TQFP770-1007 - ISP 4PORT ATMEL AVR MCU SPI/JTAG770-1005 - ISP 4PORT FOR ATMEL AVR MCU JTAG770-1004 - ISP 4PORT FOR ATMEL AVR MCU SPIATAVRISP2 - PROGRAMMER AVR IN SYSTEMATJTAGICE2 - AVR ON-CHIP D-BUG SYSTEMATAVRBFLY - KIT EVALUATION AVR BUTTERFLYATSTK502 - MOD EXPANSION AVR STARTER 500ATSTK500 - PROGRAMMER AVR STARTER KIT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

27.7.5
27.7.6
8018P–AVR–08/10
Programming the EEPROM
Reading the Flash
The EEPROM is organized in pages, see
EEPROM, the program data is latched into a page buffer. This allows one page of data to be
programmed simultaneously. The programming algorithm for the EEPROM data memory is as
follows (refer to
Data loading):
1. A: Load Command “0001 0001”.
2. G: Load Address High Byte (0x00 - 0xFF).
3. B: Load Address Low Byte (0x00 - 0xFF).
4. C: Load Data (0x00 - 0xFF).
5. E: Latch data (give PAGEL a positive pulse).
K: Repeat 3 through 5 until the entire buffer is filled.
L: Program EEPROM page
1. Set BS to “0”.
2. Give WR a negative pulse. This starts programming of the EEPROM page. RDY/BSY
3. Wait until to RDY/BSY goes high before programming the next page (See
Figure 27-4. Programming the EEPROM Waveforms
The algorithm for reading the Flash memory is as follows (refer to
page 302
1. A: Load Command “0000 0010”.
2. G: Load Address High Byte (0x00 - 0xFF).
3. B: Load Address Low Byte (0x00 - 0xFF).
4. Set OE to “0”, and BS1 to “0”. The Flash word low byte can now be read at DATA.
5. Set BS to “1”. The Flash word high byte can now be read at DATA.
6. Set OE to “1”.
goes low.
signal waveforms).
RESET +12V
RDY/BSY
PAGEL
XTAL1
DATA
XA1
XA0
BS1
BS2
WR
OE
for details on Command and Address loading):
”Programming the Flash” on page 302
0x11
A
ADDR. HIGH
G
ADDR. LOW
B
DATA
C
Table 27-8 on page
XX
E
ADDR. LOW
B
for details on Command, Address and
DATA
C
K
XX
E
299. When programming the
”Programming the Flash” on
ATmega169P
L
Figure 27-4
for
305