AT91SAM7A3-AU Atmel, AT91SAM7A3-AU Datasheet - Page 12

• Manufacturer Part Number: AT91SAM7A3-AU
• Description: IC ARM7 MCU FLASH 256K 100LQFP
• Manufacturer: Atmel
• Series: AT91SAMr

Specifications of AT91SAM7A3-AU

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 60MHz
• Connectivity: CAN, I²C, MMC, SPI, SSC, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 62
• Program Memory Size: 256KB (256K x 8)
• Program Memory Type: FLASH
• Ram Size: 32K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 1.95 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-LQFP
• Controller Family/series: AT91SAM7xx
• No. Of I/o's: 62
• Ram Memory Size: 32KB
• Cpu Speed: 60MHz
• No. Of Timers: 3
• Rohs Compliant: Yes
• Package: 100LQFP
• Device Core: ARM7TDMI
• Family Name: 91S
• Maximum Speed: 60 MHz
• Operating Supply Voltage: 3.3 V
• Data Bus Width: 32 Bit
• Number Of Programmable I/os: 62
• Interface Type: CAN/SPI/I2S/TWI/USART/USB
• On-chip Adc: 2(8-chx10-bit)
• Number Of Timers: 3
• Processor Series: AT91SAMx
• Core: ARM7TDMI
• Data Ram Size: 32 KB
• Maximum Clock Frequency: 60 MHz
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: JTRACE-ARM-2M, MDK-ARM, RL-ARM, ULINK2
• Development Tools By Supplier: AT91SAM-ICE, AT91-ISP, AT91SAM7A3-EK
• Minimum Operating Temperature: - 40 C
• Cpu Family: 91S
• Device Core Size: 32b
• Frequency (max): 60MHz
• Total Internal Ram Size: 32KB
• # I/os (max): 62
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Instruction Set Architecture: RISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 100
• Package Type: LQFP
• For Use With: AT91SAM-ICE - EMULATOR FOR AT91 ARM7/ARM9AT91SAM7A3-EK - KIT EVAL FOR AT91SAM7A3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

6. I/O Lines Considerations
6.1
6.2
6.3
6.4
6.5
6.6
12
JTAG Port Pins
Test Pin
Reset Pin
PIO Controller A and B Lines
Shutdown Logic Pins
I/O Line Drive Levels
AT91SAM7A3
TMS, TDI and TCK are schmitt trigger inputs. TMS and TCK are 5V-tolerant, TDI is not. TMS,
TDI and TCK do not integrate any resistors and have to be pulled-up externally.
TDO is an output, driven at up to VDD3V3.
The JTAGSEL pin is used to select the JTAG boundary scan when asserted at a high level.
The JTAGSEL pin integrates a permanent pull-down resistor so that it can be left unconnected
for normal operations.
The TST pin is used for manufacturing tests and integrates a pull-down resistor so that it can be
left unconnected for normal operations. Driving this line at a high level leads to unpredictable
results.
The NRST pin is bidirectional. It is handled by the on-chip reset controller and can be driven low
to provide a reset signal to the external components or asserted low externally to reset the
microcontroller. There is no constraint on the length of the reset pulse, and the reset controller
can guarantee a minimum pulse length. This allows connection of a simple push-button on the
NRST pin as system user reset, and the use of the NRST signal to reset all the components of
the system.
All the I/O lines PA0 to PA31 and PB0 to PB29 are 5V-tolerant and all integrate a programmable
pull-up resistor. Programming of this pull-up resistor is performed independently for each I/O line
through the PIO Controllers.
5V-tolerant means that the I/O lines can drive voltage level according to VDD3V3, but can be
driven with a voltage at up to 5.5V. However, driving an I/O line with a voltage over VDD3V3
while the programmable pull-up resistor is enabled creates a current path through the pull-up
resistor from the I/O line to VDDIO. Care should be taken, especially at reset, as all the I/O lines
default as inputs with pull-up resistor enabled at reset.
The SHDW pin is an open drain output. It can be tied to VDDBU with an external pull-up resistor.
The FWUP, WKUP0 and WKUP1 pins are input-only. They can accept voltages only between
0V and VDDBU. It is recommended to tie these pins either to GND or to VDDBU with an external
resistor.
All the I/O lines can draw up to 2 mA.
6042DS–ATARM–14-Dec-06