Z16F6411FI20SG Zilog, Z16F6411FI20SG Datasheet - Page 119

• Manufacturer Part Number: Z16F6411FI20SG
• Description: IC ZNEO MCU FLASH 64K 80QFP
• Manufacturer: Zilog
• Series: Encore!® ZNEOr

Specifications of Z16F6411FI20SG

• Core Processor: ZNEO
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: EBI/EMI, I²C, IrDA, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, DMA, POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 64KB (64K x 8)
• Program Memory Type: FLASH
• Ram Size: 4K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 80-BQFP
• Processor Series: Z16F6x
• Core: Zneo
• Data Bus Width: 16 bit
• Data Ram Size: 4 B
• Interface Type: ESPI, I2C, UART
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 4
• Operating Supply Voltage: 2.7 V to 3.6 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: Z16F2800100ZCOG
• Minimum Operating Temperature: 0 C
• On-chip Adc: 10 bit, 12 Channel
• For Use With: 770-1003 - ISP 4PORT FOR ZILOG ZNEO MCU269-4537 - DEV KIT FOR Z16F ZNEO
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 269-4571

PS022008-0810
Capture Elapsed Time (s)
2. Write to the timer reload high and low byte registers to set the starting count value
3. Write to the timer reload high and low byte registers to set the Reload value.
4. Enable the timer interrupt, if appropriate, and set the timer interrupt priority by writing
5. Configure the associated GPIO port pin for the timer input alternate function.
6. Write to the timer control 1 register to enable the timer. In CAPTURE and CAPTURE
In CAPTURE modes, the elapsed time from timer start to Capture event is calculated
using the following equation (start value = 1):
COMPARE Mode
In COMPARE mode, the timer counts up to the 16-bit Compare value stored in the timer
reload high and low byte registers. After reaching the compare value, the timer generates
an interrupt and counting continues (the timer value is not reset to
output alternate function is enabled, the timer output pin changes state (from Low to High
or High to Low).
If the timer reaches
Follow the steps below to configure timer for COMPARE mode and initiate the count:
1. Write to the timer control registers to:
2. Write to the timer high and low byte registers to set the starting count value.
3. Write to the timer reload high and low byte registers to set the Compare value.
4. Enable the timer interrupt, if appropriate, and set the timer interrupt priority by writing
5. When using the timer output function, configure the associated GPIO port pin for the
–
(typically
to the relevant interrupt registers.
RESTART modes, the timer begins counting. In CAPTURE COMPARE mode the
timer does not start counting until the first appropriate input transition occurs.
–
–
–
–
to the relevant interrupt registers.
timer output alternate function.
Configure the timer interrupt to be generated at the input capture event, the reload
event or both by setting
Disable the timer.
Configure the timer for COMPARE mode.
Set the prescale value.
Set the initial logic level (High or Low) for the timer output alternate function, if
required.
0001H
FFFFH
).
P R E L I M I N A R Y
=
, the timer rolls over to

------------------------------------------------------------------------------------------------------------- -
Capture Value Start Value + 1
TICONFIG
System Clock Frequency (Hz)
field.
–
0000H
and continues counting.
Product Specification


0001H
ZNEO
Prescale
). If the timer
Z16F Series
Timers
104