MC9S08QG4CDTE Freescale Semiconductor, MC9S08QG4CDTE Datasheet - Page 29

• Manufacturer Part Number: MC9S08QG4CDTE
• Description: IC MCU 4K FLASH 10MHZ 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08QG4CDTE

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: I²C, SCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 12
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 256 x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 16-TSSOP
• Processor Series: S08QG
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: SCI/SPI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 12
• Number Of Timers: 1
• Operating Supply Voltage: 1.8 V to 3.6 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08QG8E
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 8-ch x 10-bit
• Cpu Family: HCS08
• Device Core Size: 8b
• Frequency (max): 20MHz
• Total Internal Ram Size: 256Byte
• # I/os (max): 12
• Number Of Timers - General Purpose: 1
• Operating Supply Voltage (typ): 2.5/3.3V
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 1.8V
• Instruction Set Architecture: CISC
• Operating Temp Range: -40C to 85C
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: TSSOP
• Package: 16TSSOP
• Family Name: HCS08
• Maximum Speed: 20 MHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

2.2.2
Out of reset, the MCU uses an internally generated clock provided by the internal clock source (ICS)
module. The internal frequency is nominally 16-MHz and the default ICS settings will provide for a
8-MHz bus out of reset. For more information on the ICS, see
(S08ICSV1).”
The oscillator module (XOSC) in this MCU is a Pierce oscillator that can accommodate a crystal or
ceramic resonator in either of two frequency ranges selected by the RANGE bit in ICSC2. Rather than a
crystal or ceramic resonator, an external clock source can be connected to the EXTAL input pin.
Refer to
resistors such as carbon composition resistors. Wire-wound resistors, and some metal film resistors, have
too much inductance. C1 and C2 normally should be high-quality ceramic capacitors that are specifically
designed for high-frequency applications.
R
value is not generally critical. Typical systems use 1 MΩ to 10 MΩ. Higher values are sensitive to
humidity, and lower values reduce gain and (in extreme cases) could prevent startup.
C1 and C2 are typically in the 5-pF to 25-pF range and are chosen to match the requirements of a specific
crystal or resonator. Be sure to take into account printed circuit board (PCB) capacitance and MCU pin
capacitance when sizing C1 and C2. The crystal manufacturer typically specifies a load capacitance which
is the series combination of C1 and C2, which are usually the same size. As a first-order approximation,
use 10 pF as an estimate of combined pin and PCB capacitance for each oscillator pin (EXTAL and
XTAL).
2.2.3
After a power-on reset (POR), the PTA5/IRQ/TCLK/RESET pin defaults to a general-purpose input port
pin, PTA5. Setting RSTPE in SOPT1 configures the pin to be the RESET input pin. After configured as
RESET, the pin will remain RESET until the next POR. The RESET pin can be used to reset the MCU
from an external source when the pin is driven low. When enabled as the RESET pin (RSTPE = 1), an
internal pullup device is automatically enabled.
Freescale Semiconductor
F
is used to provide a bias path to keep the EXTAL input in its linear range during crystal startup, and its
Figure 2-4
Oscillator (XOSC)
Reset (Input Only)
This pin does not contain a clamp diode to V
above V
The voltage measured on the internally pulled-up RESET pin will not be
pulled to V
The RESET pullup should not be used to pull up components external to the
MCU.
In EMC-sensitive applications, an external RC filter is recommended on the
RESET pin, if enabled. See
for the following discussion. R
DD
DD
.
. The internal gates connected to this pin are pulled to V
MC9S08QG8 and MC9S08QG4 Data Sheet, Rev. 5
Figure 2-4
NOTE
NOTE
S
(when used) and R
for an example.
DD
Chapter 10, “Internal Clock Source
and should not be driven
F
should be low-inductance
Chapter 2 External Signal Description
DD
.
27