M30260F6AGP#U5A Renesas Electronics America, M30260F6AGP#U5A Datasheet - Page 248

• Manufacturer Part Number: M30260F6AGP#U5A
• Description: IC M16C MCU FLASH 48K 48LQFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/Tiny/26r

Specifications of M30260F6AGP#U5A

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 20MHz
• Connectivity: I²C, IEBus, SIO, UART/USART
• Peripherals: DMA, PWM, Voltage Detect, WDT
• Number Of I /o: 39
• Program Memory Size: 48KB (48K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 48-LQFP
• Cpu Family: R8C
• Device Core Size: 16b
• Frequency (max): 20MHz
• Interface Type: UART
• Total Internal Ram Size: 2KB
• # I/os (max): 39
• Number Of Timers - General Purpose: 8
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 3V
• On-chip Adc: 12-chx10-bit
• Instruction Set Architecture: CISC
• Operating Temp Range: -20C to 85C
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 48
• Package Type: LQFP
• Package: 48LQFP
• Family Name: R8C
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 39
• Number Of Timers: 8
• For Use With: R0K33026AS000BE - KIT DEV EVALUATION M16C/26A
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Compliant

R
R
M
e
E
1
. v
J
Table 16.1. Unassigned Pin Handling in Single-chip Mode
Figure 16.7. Unassigned Pins Handling
6
NOTES:
0
Ports P1, P6 to P10
2
C
X
AV
AV
9
X
0 .
B
OUT
IN
2 /
1. When setting the port for output mode and leave it open, be aware that the port remains in input mode until it is
2. Make sure the unused pins are processed with the shortest possible wiring from the microcomputer pins (within 2
3. With external clock or VCC input to XIN pin.
4. When using the 48-pin package, set PACR2, PACR1, PACR0 to "100
5. When the main clock oscillation circuit is not used, set the CM05 bit in the CM0 register to “0” (main clock stops)
0
0
CC
SS
6
2
switched to output mode in a program after reset. For this reason, the voltage level on the pin becomes
indeterminate, causing the power supply current to increase while the port remains in input mode. Futhermore,
by considering a possibility that the contents of the direction registers could be changed by noise or noise-
induced runaway, it is recommended that the contents of the direction registers be periodically reset in software,
for the increased reliability of the program.
cm).
PACR2, PACR1, PACR0 to "001
to reduce power consumption.
0
A
F
, V
(3)
2
e
Pin name
G
0 -
b
REF
1 .
o r
2
0
, 5
u
0
p
2
0
(
M
0
7
1
6
C
page 229
2 /
6
NOTE:
, A
Open
Connect via resistor to V
Connect to V
Connect to V
After setting for input mode, connect every pin to V
or after setting for output mode, leave these pins open.
1. When using the 48-pin package, set PACR2, PACR1, PACR0 to "100
M
When using the 42pin-package, set PACR2, PACR1, PACR0 to "001
1
f o
6
3
C
2
2 /
9
2
".
6
, B
CC
SS
In single-chip mode
M
Microcomputer
1
Port P1, P6 to P10
6
(1)
C
2 /
6
(Output mode)
) T
(Input mode)
(Input mode)
CC
·
·
·
AV
AV
X
V
(pull-up)
OUT
REF
X
CC
SS
IN
Connection
Open
Open
(5)
V
·
·
·
CC
2
". When using the 42-pin package, set
V
SS
SS
via a resistor(pull-down);
(1, 2, 4)
16. Programmable I/O Ports
2
2
".
".