PIC16F88-E/P Microchip Technology, PIC16F88-E/P Datasheet - Page 149

• Manufacturer Part Number: PIC16F88-E/P
• Description: IC MCU FLASH 4KX14 EEPROM 18DIP
• Manufacturer: Microchip Technology
• Series: PIC® 16Fr

Specifications of PIC16F88-E/P

• Core Size: 8-Bit
• Program Memory Size: 7KB (4K x 14)
• Core Processor: PIC
• Speed: 20MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 16
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 368 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 7x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 18-DIP (0.300", 7.62mm)
• Controller Family/series: PIC16F
• No. Of I/o's: 16
• Eeprom Memory Size: 256Byte
• Ram Memory Size: 368Byte
• Cpu Speed: 20MHz
• No. Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: ACICE0202 - ADAPTER MPLABICE 18P 300 MIL
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

15.14 In-Circuit Debugger
When the DEBUG bit in the Configuration Word is
programmed to a ‘0’, the In-Circuit Debugger function-
ality is enabled. This function allows simple debugging
functions when used with MPLAB
microcontroller has this feature enabled, some of the
resources are not available for general use. Table 15-7
shows which features are consumed by the background
debugger.
TABLE 15-7:
To use the In-Circuit Debugger function of the micro-
controller, the design must implement In-Circuit Serial
Programming connections to RA5/MCLR/V
GND, RB7 and RB6. This will interface to the In-Circuit
Debugger module available from Microchip, or one of
the third party development tool companies.
15.15 Program Verification/Code
If
programmed, the on-chip program memory can be
read out for verification purposes.
15.16 ID Locations
Four memory locations (2000h-2003h) are designated
as ID locations, where the user can store checksum or
other code identification numbers. These locations are
not accessible during normal execution but are
readable and writable during program/verify. It is
recommended that only the four Least Significant bits
of the ID location are used.
15.17 In-Circuit Serial Programming
PIC16F87/88 microcontrollers can be serially pro-
grammed while in the end application circuit. This is
simply done with two lines for clock and data and three
other lines for power, ground and the programming
voltage (see Figure 15-13 for an example). This allows
customers to manufacture boards with unprogrammed
devices and then program the microcontroller just
before shipping the product. This also allows the most
recent firmware or a custom firmware to be
programmed.
 2005 Microchip Technology Inc.
I/O pins
Stack
Program Memory
Data Memory
the
Protection
code
protection
DEBUGGER RESOURCES
0x070 (0x0F0, 0x170, 0x1F0)
Address 0000h must be NOP
bit(s)
Last 100h words
0x1EB-0x1EF
RB6, RB7
1 level
®
have
ICD. When the
not
PP
, V
been
DD
,
For more information on serial programming, please
refer to the “PIC16F87/88 Flash Memory Programming
Specification” (DS39607).
FIGURE 15-13:
* Isolation devices (as required).
†
Note:
RB3/PGM
RB3 only used in LVP mode.
External
Connector
Signals
Data I/O
CLK
+5V
V
0V
PP
The Timer1 oscillator shares the T1OSI
and T1OSO pins with the PGD and PGC
pins
debugging.
When using the Timer1 oscillator, In-
Circuit Serial Programming™ (ICSP™)
may not function correctly (high voltage or
low voltage), or the In-Circuit Debugger
(ICD) may not communicate with the
controller. As a result of using either ICSP
or ICD, the Timer1 crystal may be
damaged.
If ICSP or ICD operations are required, the
crystal should be disconnected from the
circuit (disconnect either lead), or installed
after programming. The oscillator loading
capacitors may remain in-circuit during
ICSP or ICD operation.
*
used
To Normal
Connections
To Normal
Connections
PIC16F87/88
TYPICAL IN-CIRCUIT
SERIAL PROGRAMMING
CONNECTION
*
*
for
*
programming
DS30487C-page 147
V
V
RA5/MCLR/V
RB6
RB7
RB3
PIC16F87/88
DD
SS
†
V
DD
PP
and