ATMEGA1280V-8AUR Atmel, ATMEGA1280V-8AUR Datasheet - Page 89

• Manufacturer Part Number: ATMEGA1280V-8AUR
• Description: MCU AVR 128K FLASH 8MHZ 100TQFP
• Manufacturer: Atmel
• Series: AVR® ATmegar

Specifications of ATMEGA1280V-8AUR

• Core Processor: AVR
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: EBI/EMI, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 86
• Program Memory Size: 128KB (64K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 4K x 8
• Ram Size: 8K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 100-TQFP, 100-VQFP
• For Use With: ATSTK600-TQFP100 - STK600 SOCKET/ADAPTER 100-TQFPATSTK503 - STARTER KIT AVR EXP MODULE 100P
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

12.3.6
2549M–AVR–09/10
Alternate Functions of Port F
The Port F has an alternate function as analog input for the ADC as shown in
some Port F pins are configured as outputs, it is essential that these do not switch when a con-
version is in progress. This might corrupt the result of the conversion. If the JTAG interface is
enabled, the pull-up resistors on pins PF7(TDI), PF5(TMS), and PF4(TCK) will be activated even
if a Reset occurs.
Table 12-18. Port F Pins Alternate Functions
• TDI, ADC7 – Port F, Bit 7
ADC7, Analog to Digital Converter, Channel 7.
TDI, JTAG Test Data In: Serial input data to be shifted in to the Instruction Register or Data Reg-
ister (scan chains). When the JTAG interface is enabled, this pin can not be used as an I/O pin.
• TDO, ADC6 – Port F, Bit 6
ADC6, Analog to Digital Converter, Channel 6.
TDO, JTAG Test Data Out: Serial output data from Instruction Register or Data Register. When
the JTAG interface is enabled, this pin can not be used as an I/O pin.
The TDO pin is tri-stated unless TAP states that shift out data are entered.
• TMS, ADC5 – Port F, Bit 5
ADC5, Analog to Digital Converter, Channel 5.
TMS, JTAG Test Mode Select: This pin is used for navigating through the TAP-controller state
machine. When the JTAG interface is enabled, this pin can not be used as an I/O pin.
• TCK, ADC4 – Port F, Bit 4
ADC4, Analog to Digital Converter, Channel 4.
TCK, JTAG Test Clock: JTAG operation is synchronous to TCK. When the JTAG interface is
enabled, this pin can not be used as an I/O pin.
• ADC3 – ADC0 – Port F, Bit 3:0
Analog to Digital Converter, Channel 3:0.
Port Pin
PF7
PF6
PF5
PF4
PF3
PF2
PF1
PF0
ADC5/TMS (ADC input channel 5 or JTAG Test Mode Select)
ADC6/TDO (ADC input channel 6 or JTAG Test Data Output)
ADC7/TDI (ADC input channel 7 or JTAG Test Data Input)
ADC4/TCK (ADC input channel 4 or JTAG Test ClocK)
ATmega640/1280/1281/2560/2561
ADC3 (ADC input channel 3)
ADC2 (ADC input channel 2)
ADC1 (ADC input channel 1)
ADC0 (ADC input channel 0)
Alternate Function
Table
12-18. If
89