PIC17LC756A-08I/L Microchip Technology, PIC17LC756A-08I/L Datasheet - Page 145

• Manufacturer Part Number: PIC17LC756A-08I/L
• Description: IC MCU OTP 16KX16 A/D 68PLCC
• Manufacturer: Microchip Technology
• Series: PIC® 17Cr

Specifications of PIC17LC756A-08I/L

• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 50
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: OTP
• Ram Size: 902 x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 12x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 68-PLCC
• Processor Series: PIC17LC
• Core: PIC
• Data Bus Width: 8 bit
• Data Ram Size: 902 B
• Interface Type: I2C, MSSP, RS- 232, SCI, SPI, USART
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 50
• Number Of Timers: 8
• Operating Supply Voltage: 3 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

15.2.1.1
Once the MSSP module has been enabled, it waits for
a START condition to occur. Following the START con-
dition, the 8-bits are shifted into the SSPSR register. All
incoming bits are sampled with the rising edge of the
clock (SCL) line. The value of register SSPSR<7:1> is
compared to the value of the SSPADD register. The
address is compared on the falling edge of the eighth
clock (SCL) pulse. If the addresses match and the BF
and SSPOV bits are clear, the following events occur:
a)
b)
c)
d)
In 10-bit address mode, two address bytes need to be
received by the slave. The five Most Significant bits
(MSbs) of the first address byte specify if this is a 10-bit
address. Bit R/W (SSPSTAT<2>) must specify a write so
the slave device will receive the second address byte.
For a 10-bit address, the first byte would equal ‘1111 0
A9 A8 0’, where A9 and A8 are the two MSbs of the
address. The sequence of events for a 10-bit address is
as follows, with steps 7- 9 for slave-transmitter:
1.
2.
3.
4.
TABLE 15-2:
Note 1: Shaded cells show the conditions where the user software did not properly clear the overflow condition.
2000 Microchip Technology Inc.
Transfer is Received
Status Bits as Data
The SSPSR register value is loaded into the
SSPBUF register on the falling edge of the 8th
SCL pulse.
The buffer full bit, BF, is set on the falling edge
of the 8th SCL pulse.
An ACK pulse is generated.
SSP interrupt flag bit, SSPIF (PIR2<7>), is set
(interrupt is generated if enabled) - on the falling
edge of the 9th SCL pulse.
Receive first (high) byte of Address (bits SSPIF,
BF and bit UA (SSPSTAT<1>) are set).
Update the SSPADD register with second (low)
byte of Address (clears bit UA and releases the
SCL line).
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Receive second (low) byte of Address (bits
SSPIF, BF and UA are set).
BF
0
1
1
0
Addressing
SSPOV
DATA TRANSFER RECEIVED BYTE ACTIONS
0
0
1
1
SSPSR
Yes
Yes
No
No
SSPBUF
5.
6.
7.
8.
9.
15.2.1.2
When the R/W bit of the address byte is clear and an
address match occurs, the R/W bit of the SSPSTAT
register is cleared. The received address is loaded into
the SSPBUF register.
When the address byte overflow condition exists, then
no acknowledge (ACK) pulse is given. An overflow con-
dition is defined as either bit BF (SSPSTAT<0>) is set,
or bit SSPOV (SSPCON1<6>) is set.
An SSP interrupt is generated for each data transfer
byte. Flag bit SSPIF (PIR2<7>) must be cleared in soft-
ware. The SSPSTAT register is used to determine the
status of the received byte.
Generate ACK
Note:
Note:
Update the SSPADD register with the first (high)
byte of Address. This will clear bit UA and
release the SCL line.
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Receive Repeated Start condition.
Receive first (high) byte of Address (bits SSPIF
and BF are set).
Read the SSPBUF register (clears bit BF) and
clear flag bit SSPIF.
Pulse
Yes
No
No
No
Following the Repeated Start condition
(step 7) in 10-bit mode, the user only
needs to match the first 7-bit address. The
user does not update the SSPADD for the
second half of the address.
The SSPBUF will be loaded if the SSPOV
bit is set and the BF flag is cleared. If a
read of the SSPBUF was performed, but
the user did not clear the state of the
SSPOV bit before the next receive
occurred, the ACK is not sent and the SSP-
BUF is updated.
Slave Reception
PIC17C7XX
(SSP Interrupt occurs
Set bit SSPIF
if enabled)
DS30289B-page 145
Yes
Yes
Yes
Yes