P87C51RC2BN,112 NXP Semiconductors, P87C51RC2BN,112 Datasheet - Page 11

• Manufacturer Part Number: P87C51RC2BN,112
• Description: IC 80C51 MCU 512 RAM 40DIP
• Manufacturer: NXP Semiconductors
• Series: 87Cr

Specifications of P87C51RC2BN,112

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 33MHz
• Connectivity: EBI/EMI, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: OTP
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 40-DIP (0.600", 15.24mm)
• Cpu Family: 87C
• Device Core: 80C51
• Device Core Size: 8b
• Frequency (max): 33MHz
• Interface Type: UART
• Total Internal Ram Size: 512Byte
• # I/os (max): 32
• Number Of Timers - General Purpose: 3
• Operating Supply Voltage (typ): 3.3/5V
• Operating Supply Voltage (max): 5.5V
• Operating Supply Voltage (min): 2.7V
• Instruction Set Architecture: CISC
• Operating Temp Range: 0C to 70C
• Operating Temperature Classification: Commercial
• Mounting: Through Hole
• Pin Count: 40
• Package Type: PDIP
• Processor Series: P87C5x
• Core: 80C51
• Data Bus Width: 8 bit
• Maximum Clock Frequency: 16 MHz
• Operating Supply Voltage: 2.7 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• 3rd Party Development Tools: PK51, CA51, A51, ULINK2
• Minimum Operating Temperature: 0 C
• For Use With: OM10064 - EMULATOR 80C51 PDS51-MK2
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Data Converters: -
• Lead Free Status / Rohs Status: Compliant
• Other names: 935272150112; P87C51RC2BN; P87C51RC2BN

Philips Semiconductors
CLOCK CONTROL REGISTER (CKCON)
This device allows control of the 6-clock/12-clock mode by means of
both an SFR bit (X2) and an OTP bit. The OTP clock control bit
Also please note that the clock divider applies to the serial port for
modes 0 & 2 (fixed baud rate modes). This is because modes 1 & 3
(variable baud rate modes) use either Timer 1 or Timer 2.
Below is the truth table for the CPU clock mode.
Table 1.
2003 Jan 24
OX2 clock mode bit
(can only be set by
parallel programmer)
erased
erased
programmed
80C51 8-bit microcontroller family
with 512B/1KB RAM, low voltage (2.7 to 5.5 V), low power, high
speed (30/33 MHz)
CKCON
BIT
CKCON.7
CKCON.6
CKCON.5
CKCON.4
CKCON.3
CKCON.2
CKCON.1
CKCON.0
Not Bit Addressable
Address = 8Fh
SYMBOL
–
X2
X2 bit
(CKCON.0)
0
1
X
FUNCTION
Reserved.
Reserved.
Reserved.
Reserved.
Reserved.
Reserved.
Reserved.
CPU clock; 1 = 6 clocks for each machine cycle, 0 = 12 clocks for each machine cycle
–
7
8KB/16KB/32KB/64KB OTP
CPU clock mode
12-clock mode
(default)
6-clock mode
6-clock mode
–
6
Figure 1. Clock control (CKCON) register
–
5
4
–
11
3
–
OX2, when programmed (6-clock mode), supersedes the X2 bit
(CKCON.0). The CKCON register is shown below in Figure 1.
RESET
A reset is accomplished by holding the RST pin high for at least two
machine cycles (12 oscillator periods in 6-clock mode, or 24 oscillator
periods in 12-clock mode), while the oscillator is running. To ensure a
good power-on reset, the RST pin must be high long enough to allow
the oscillator time to start up (normally a few milliseconds) plus two
machine cycles. At power-on, the voltage on V
come up at the same time for a proper start-up. Ports 1, 2, and 3 will
asynchronously be driven to their reset condition when a voltage
above V
The value on the EA pin is latched when RST is deasserted and has
no further effect.
IH1
2
–
(min.) is applied to RST.
P87C51RA2/RB2/RC2/RD2
1
–
0
X2
Reset Value = x0000000B
CC
and RST must
SU01689
Product data