ST7FMC1K4T6 STMicroelectronics, ST7FMC1K4T6 Datasheet - Page 42

• Manufacturer Part Number: ST7FMC1K4T6
• Description: MCU 8BIT 16K FLASH 32TQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FMC1K4T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LINSCI
• Peripherals: LVD, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 17
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-LQFP
• Processor Series: ST7FMC1x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 3
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7MC-KIT/BLDC, ST7MDT50-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 16 Channel
• For Use With: 497-8402 - BOARD EVAL COMPLETE INVERTER497-8400 - KIT IGBT PWR MODULE CTRL ST7MC497-4734 - EVAL KIT 3KW POWER DRIVER BOARD497-4733 - EVAL KIT 1KW POWER DRIVER BOARD497-4732 - EVAL KIT 300W POWER DRIVER BOARD497-4731 - EVAL KIT PWR DRIVER CONTROL BRD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-4866

ST7MC1xx/ST7MC2xx
INTERRUPTS (Cont’d)
7.3 INTERRUPTS AND LOW POWER MODES
All interrupts allow the processor to exit the Wait
low power mode. On the contrary, only external
and other specified interrupts allow the processor
to exit from the Halt modes (see column “Exit from
Halt” in “Interrupt Mapping” table). When several
pending interrupts are present while exiting Halt
mode, the first one serviced can only be an inter-
rupt with exit from Halt mode capability and it is se-
lected through the same decision process shown
in
Note: If an interrupt, that is not able to Exit from
Halt mode, is pending with the highest priority
when exiting Halt mode, this interrupt is serviced
after the first one serviced.
Figure 22. Concurrent Interrupt Management
Figure 23. Nested Interrupt Management
42/309
1
Figure
21.
11 / 10
11 / 10
MAIN
MAIN
RIM
RIM
IT2
IT2
IT1
IT1
IT4
MCES
MCES
IT1
IT4
IT0
IT0
7.4 CONCURRENT & NESTED MANAGEMENT
The following
different interrupt management modes. The first is
called concurrent mode and does not allow an in-
terrupt to be interrupted, unlike the nested mode in
Figure
in this order from the lowest to the highest: MAIN,
IT4, IT3, IT2, IT1, IT0, MCES. The software priority
is given for each interrupt.
Warning: A stack overflow may occur without no-
tifying the software of the failure.
IT3
IT3
IT1
23. The interrupt hardware priority is given
IT4
IT2
Figure 22
10
10
SOFTWARE
PRIORITY
LEVEL
SOFTWARE
PRIORITY
LEVEL
MAIN
MAIN
and
3
3
3
3
3
3
3/0
3
3
2
1
3
3
3/0
Figure 23
I1
I1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
0 0
0 1
1 1
1 1
show two
I0
I0