ST72F361J9T6 STMicroelectronics, ST72F361J9T6 Datasheet - Page 30

• Manufacturer Part Number: ST72F361J9T6
• Description: IC MCU 8BIT 60K FLASH 44-LQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F361J9T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LINSCI, SPI
• Peripherals: LVD, POR, PWM, WDT
• Number Of I /o: 32
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-LQFP
• Processor Series: ST72F3x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 2 KB
• Interface Type: LINSCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 34
• Number Of Timers: 2
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST72F36X-SK/RAIS, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 11 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

ST72361
INTERRUPTS (Cont’d)
7.3 INTERRUPTS AND LOW POWER MODES
All interrupts allow the processor to exit the WAIT
low power mode. On the contrary, only external
and other specified interrupts allow the processor
to exit from the HALT modes (see column “Exit
from HALT” in “Interrupt Mapping” table). When
several pending interrupts are present while exit-
ing HALT mode, the first one serviced can only be
an interrupt with exit from HALT mode capability
and it is selected through the same decision proc-
ess shown in
Note: If an interrupt, that is not able to Exit from
HALT mode, is pending with the highest priority
when exiting HALT mode, this interrupt is serviced
after the first one serviced.
Figure 19. Concurrent Interrupt Management
Figure 20. Nested Interrupt Management
30/225
11 / 10
11 / 10
MAIN
MAIN
Figure
RIM
RIM
18.
IT2
IT2
IT1
IT1
IT4
TLI
TLI
IT1
IT4
IT0
IT0
7.4 CONCURRENT & NESTED MANAGEMENT
The following
different interrupt management modes. The first is
called concurrent mode and does not allow an in-
terrupt to be interrupted, unlike the nested mode in
Figure
in this order from the lowest to the highest: MAIN,
IT4, IT3, IT2, IT1, IT0, TLI. The software priority is
given for each interrupt.
Warning: A stack overflow may occur without no-
tifying the software of the failure.
IT3
IT3
IT1
20. The interrupt hardware priority is given
IT4
IT2
Figure 19
10
10
SOFTWARE
PRIORITY
LEVEL
SOFTWARE
PRIORITY
LEVEL
MAIN
MAIN
and
3
3
3
3
3
3
3/0
3
3
2
1
3
3
3/0
Figure 20
I1
I1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
1 1
0 0
0 1
1 1
1 1
show two
I0
I0