ST72F63BK4M1 STMicroelectronics, ST72F63BK4M1 Datasheet - Page 54

• Manufacturer Part Number: ST72F63BK4M1
• Description: IC MCU 8BIT LS 16K 34-SOIC
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST72F63BK4M1

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: I²C, SCI, USB
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 19
• Program Memory Size: 16KB (16K x 8)
• Program Memory Type: FLASH
• Ram Size: 512 x 8
• Voltage - Supply (vcc/vdd): 4 V ~ 5.5 V
• Data Converters: A/D 8x8b
• Oscillator Type: Internal
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 34-SOIC (7.5mm Width)
• Processor Series: ST72F6x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 512 B
• Interface Type: I2C, SCI, USB
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 27
• Number Of Timers: 2 x 16 bit
• Operating Supply Voltage: 4 V to 5.5 V
• Maximum Operating Temperature: + 70 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7MDTU3-EPB/US, ST72F63B-SK/RAIS, ST7MDTU3-EMU3, STX-RLINK
• Minimum Operating Temperature: 0 C
• On-chip Adc: 8 bit
• For Use With: 497-5521 - EVAL BOARD LOW SPEED USB
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-2115-5

On-chip peripherals
11
11.1
11.1.1
11.1.2
11.1.3
54/186
On-chip peripherals
Watchdog timer (WDG)
Introduction
The Watchdog timer is used to detect the occurrence of a software fault, usually generated
by external interference or by unforeseen logical conditions, which causes the application
program to abandon its normal sequence. The Watchdog circuit generates an MCU reset on
expiry of a programmed time period, unless the program refreshes the counter’s contents
before the T6 bit becomes cleared.
Main features
●
●
●
●
●
Functional description
The counter value stored in the CR register (bits T6:T0), is decremented every 49,152
machine cycles, and the length of the timeout period can be programmed by the user in 64
increments.
If the watchdog is activated (the WDGA bit is set) and when the 7-bit timer (bits T6:T0) rolls
over from 40h to 3Fh (T6 becomes cleared), it initiates a reset cycle by driving low the reset
pin for t
The application program must write in the CR register at regular intervals during normal
operation to prevent an MCU reset. This down counter is free-running: it counts down even if
the watchdog is disabled. The value to be stored in the CR register must be between FFh
and C0h (see
●
●
●
Programmable free-running counter (64 increments of 49,152 CPU cycles)
Programmable reset
Reset (if watchdog activated) when the T6 bit reaches zero
Optional reset on HALT instruction (configurable by option byte)
Hardware Watchdog selectable by option byte.
The WDGA bit is set (watchdog enabled)
The T6 bit is set to prevent generating an immediate reset
The T5:T0 bits contain the number of increments which represents the time delay
before the watchdog produces a reset.
W(RSTL)out
Table
(see
17):
Table
72).
Doc ID 7516 Rev 8
ST7263Bxx