ST7FMC2M9T6 STMicroelectronics, ST7FMC2M9T6 Datasheet - Page 211

• Manufacturer Part Number: ST7FMC2M9T6
• Description: MCU 8BIT 60K FLASH 80TQFP
• Manufacturer: STMicroelectronics
• Series: ST7r

Specifications of ST7FMC2M9T6

• Core Processor: ST7
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: LINSCI, SPI
• Peripherals: LVD, Motor Control PWM, POR, PWM, WDT
• Number Of I /o: 60
• Program Memory Size: 60KB (60K x 8)
• Program Memory Type: FLASH
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 3.8 V ~ 5.5 V
• Data Converters: A/D 16x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 80-TQFP, 80-VQFP
• Processor Series: ST7FMC2x
• Core: ST7
• Data Bus Width: 8 bit
• Data Ram Size: 1536 B
• Interface Type: SCI, SPI
• Maximum Clock Frequency: 8 MHz
• Number Of Programmable I/os: 60
• Number Of Timers: 5
• Operating Supply Voltage: 4.5 V to 5.5 V
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: ST7MC-KIT/BLDC, ST7MDT50-EMU3, STX-RLINK
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit
• For Use With: 497-8402 - BOARD EVAL COMPLETE INVERTER497-8400 - KIT IGBT PWR MODULE CTRL ST7MC497-6408 - BOARD EVAL BLDC SENSORLESS MOTOR497-4734 - EVAL KIT 3KW POWER DRIVER BOARD497-4733 - EVAL KIT 1KW POWER DRIVER BOARD497-4732 - EVAL KIT 300W POWER DRIVER BOARD497-4731 - EVAL KIT PWR DRIVER CONTROL BRD
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details
• Other names: 497-4867

MOTOR CONTROLLER (Cont’d)
Effect on PWM generator: the PWM generator
12-bit counter is reset as soon as CKE = 0; this en-
sures that the PWM signals start properly in all
cases. When these bits are set, all registers with
preload on Update event are transferred to active
registers.
Bit 5 = SR: Sensor ON/OFF.
0: Sensorless mode
1: Position Sensor mode
Table 57. Sensor Mode Selection
See also
Bit 4 = DAC: Direct Access to phase state register.
0: No Direct Access (reset value). In this mode the
1: Direct Access enabled. In this mode, write a val-
Note: In Direct Access Mode (DAC bit is set in
SR
bit
0
1
preload value of the MPHST and MCRB regis-
ters is taken into account at the C event.
ue in the MPHST register to access the outputs
directly.
MCRA register), a C event is generated as soon
as there is a write access to the OO[5:0] bits in
MPHST register. In this case, the PWM low/high
selection is done by the OS0 bit in the MCRB
register.
not used
Sensors
Sensors
Mode
used
Table 61
disabled
OS[2:0]
enabled
OS[2:0]
OS1
bits
bits
and
Table 62
“Between C
“Between C
and “between Z&C
and “between Z&C
“between D&Z” behaviour
Behaviour of the output
haviour
haviour
PWM
n
n
&D” behaviour,
&Z” behaviour
n+1
n+1
” be-
” be-
Table 58. DAC Bit Meaning
Bit 3 = V0C1: Voltage/Current Mode
0: Voltage Mode
1: Current Mode
Bit 2 = SWA: Switched/Autoswitched Mode
0: Switched Mode
1: Autoswitched Mode
Note 1 : after reset, in autoswitched mode (SWA
=1) , the motor control peripheral is waiting for a C
commutation event.
Note 2: After reset, a C event is immediately gen-
erated when CKE and SWA are simultaneaously
set due to a nil value of MCOMP.
Bit 1 = PZ: Protection from parasitic Zero-crossing
event detection
0: Protection disabled
1: Protection enabled
Note: If the PZ bit is set, the Z event filter
(ZEF[3:0] in the MZFR register is ignored.
Bit 0 = DCB: Data Capture bit
0: Use MZPRV (Z
1: Use MZREG (Z
Table 59. Multiplier Result
MOE
DCB bit
bit
0
1
1
0
1
DAC
bit
0
1
x
MCOMP = MWGHT x MZREG / 256
MCOMP = MWGHT x MZPRV / 256
MPHST register value (depending on
Reset state depending on the option
N
N
MPOL, MPAR register values and
-1) for multiplication
) for multiplication
PWM setting) see
Commutation Delay
ST7MC1xx/ST7MC2xx
Effect on Output
running mode.
Standard
bit
Table 74
211/309
1