MC9S08FL8CBM Freescale Semiconductor, MC9S08FL8CBM Datasheet - Page 10

• Manufacturer Part Number: MC9S08FL8CBM
• Description: MCU 8BIT 8K FLASH 32-SDIP
• Manufacturer: Freescale Semiconductor
• Series: HCS08r

Specifications of MC9S08FL8CBM

• Core Processor: HCS08
• Core Size: 8-Bit
• Speed: 20MHz
• Connectivity: SCI
• Peripherals: LVD, PWM, WDT
• Number Of I /o: 30
• Program Memory Size: 8KB (8K x 8)
• Program Memory Type: FLASH
• Ram Size: 768 x 8
• Voltage - Supply (vcc/vdd): 4.5 V ~ 5.5 V
• Data Converters: A/D 12x8b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 32-SDIP (0.400", 10.16mm)
• Processor Series: S08FL
• Core: HCS08
• Data Bus Width: 8 bit
• Data Ram Size: 768 B
• Interface Type: SCI
• Maximum Clock Frequency: 20 MHz
• Number Of Programmable I/os: 30
• Number Of Timers: 1
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• 3rd Party Development Tools: EWS08
• Development Tools By Supplier: DEMO9S08FL16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12-ch x 8-bit
• Controller Family/series: HCS08
• No. Of I/o's: 30
• Ram Memory Size: 768Byte
• Cpu Speed: 20MHz
• No. Of Timers: 1
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

Electrical Characteristics
5.4
This section provides information about operating temperature range, power dissipation, and package
thermal resistance. Power dissipation on I/O pins is usually small compared to the power dissipation in
on-chip logic and voltage regulator circuits, and it is user-determined rather than being controlled by the
MCU design. To take P
voltage and V
pin current (heavy loads), the difference between pin voltage and V
The average chip-junction temperature (T
10
Thermal Characteristics
1
2
3
SS
Supply voltage
Maximum current into V
Digital input voltage
Instantaneous maximum current
Storage temperature range
Input must be current limited to the value specified. To determine the value of the required
current-limiting resistor, calculate resistance values for positive (V
voltages, then use the larger of the two resistance values.
All functional non-supply pins, except for PTA5 are internally clamped to V
Power supply must maintain regulation within operating V
operating maximum current conditions. If positive injection current (V
I
out of regulation. Ensure external V
current. This will be the greatest risk when the MCU is not consuming power. Examples are: if
no system clock is present, or if the clock rate is very low (which would reduce overall power
consumption).
DD
Single pin limit (applies to all port pins)
or V
, the injection current may flow out of V
Operating temperature range
(packaged)
Thermal resistance
Thermal resistance
Single-layer board
Four-layer board
DD
I/O
and multiply by the pin current for each I/O pin. Except in cases of unusually high
32-pin SDIP
32-pin LQFP
32-pin SDIP
32-pin LQFP
into account in power calculations, determine the difference between actual pin
Rating
Rating
DD
Table 3. Absolute Maximum Ratings
MC9S08FL16 Series Data Sheet, Rev. 3
Table 4. Thermal Characteristics
J
) in C can be obtained from:
DD
load will shunt current greater than maximum injection
1, 2, 3
DD
and could result in external power supply going
Symbol


T
JA
JA
A
Symbol
V
T
I
V
DD
I
DD
stg
D
In
DD
range during instantaneous and
SS
–40 to 85
DD
T
Value
–0.3 to V
L
) and negative (V
or V
60
85
35
56
to T
In
–0.3 to 5.8
–55 to 150
> V
Value
H
120
25
DD
SS
DD
DD
) is greater than
and V
will be very small.
+ 0.3
C/W
C/W
Unit
DD
C
Freescale Semiconductor
SS
.
) clamp
Unit
mA
mA
C
V
V