MC908QB4MDTE Freescale Semiconductor, MC908QB4MDTE Datasheet - Page 101

• Manufacturer Part Number: MC908QB4MDTE
• Description: IC MCU 8BIT 4K FLASH 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QB4MDTE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 16-TSSOP
• Processor Series: HC08QB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: 3-Wire, ESCI, SPI, UART
• Number Of Programmable I/os: 13
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

ECFS1:ECFS0 — External Crystal Frequency Select Bits
ECGON — External Clock Generator On Bit
ECGST — External Clock Status Bit
11.8.2 Oscillator Trim Register (OSCTRIM)
TRIM7–TRIM0 — Internal Oscillator Trim Factor Bits
Freescale Semiconductor
These read/write bits enable the specific amplifier for the crystal frequency range. Refer to oscillator
characteristics table in the Electricals section for information on maximum external clock frequency
versus supply voltage.
This read/write bit enables the OSC1 pin as the clock input to the MCU, so that the switching process
can be initiated. This bit is cleared by reset. This bit is ignored in monitor mode with the internal
oscillator bypassed.
This read-only bit indicates whether an external clock source is engaged to drive the system clock.
These read/write bits change the internal capacitance used by the internal oscillator. By measuring the
period of the internal clock and adjusting this factor accordingly, the frequency of the internal clock can
be fine tuned. Increasing (decreasing) this factor by one increases (decreases) the period by
approximately 0.2% of the untrimmed oscillator period. The oscillator period is based on the oscillator
frequency selected by the ICFS bits in OSCSC.
Applications using the internal oscillator should copy the internal oscillator trim value at location $FFC0
into this register to trim the clock source.
1 = External clock enabled
0 = External clock disabled
1 = An external clock source engaged
0 = An external clock source disengaged
Reset:
Read:
Write:
ECFS1
0
0
1
1
TRIM7
Bit 7
1
Figure 11-5. Oscillator Trim Register (OSCTRIM)
TRIM6
ECFS0
6
0
0
1
0
1
MC68HC908QB8 Data Sheet, Rev. 3
TRIM5
8 MHz – 32 MHz
1 MHz – 8 MHz
32 kHz – 100 kHz
Reserved
5
0
TRIM4
4
0
External Crystal Frequency
TRIM3
3
0
TRIM2
2
0
TRIM1
1
0
TRIM0
Bit 0
0
Registers
101