MC908QB4MDTE Freescale Semiconductor, MC908QB4MDTE Datasheet - Page 172

• Manufacturer Part Number: MC908QB4MDTE
• Description: IC MCU 8BIT 4K FLASH 16-TSSOP
• Manufacturer: Freescale Semiconductor
• Series: HC08r

Specifications of MC908QB4MDTE

• Core Processor: HC08
• Core Size: 8-Bit
• Speed: 8MHz
• Connectivity: SCI, SPI
• Peripherals: LVD, POR, PWM
• Number Of I /o: 13
• Program Memory Size: 4KB (4K x 8)
• Program Memory Type: FLASH
• Ram Size: 128 x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 5.5 V
• Data Converters: A/D 10x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 16-TSSOP
• Processor Series: HC08QB
• Core: HC08
• Data Bus Width: 8 bit
• Data Ram Size: 256 B
• Interface Type: 3-Wire, ESCI, SPI, UART
• Number Of Programmable I/os: 13
• Number Of Timers: 4
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Development Tools By Supplier: FSICEBASE, M68CBL05AE, DEMO908QB8, DEMO908QC16
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 10 bit, 10 Channel
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Lead Free Status / Rohs Status: Details

Serial Peripheral Interface (SPI) Module
SPTIE— SPI Transmit Interrupt Enable
15.8.2 SPI Status and Control Register
The SPI status and control register contains flags to signal these conditions:
The SPI status and control register also contains bits that perform these functions:
SPRF — SPI Receiver Full Bit
ERRIE — Error Interrupt Enable Bit
OVRF — Overflow Bit
172
This read/write bit enables interrupt requests generated by the SPTE bit. SPTE is set when a byte
transfers from the transmit data register to the shift register.
•
•
•
•
•
•
•
This clearable, read-only flag is set each time a byte transfers from the shift register to the receive data
register. SPRF generates a interrupt request if the SPRIE bit in the SPI control register is set also.
During an SPRF interrupt, user software can clear SPRF by reading the SPI status and control register
with SPRF set followed by a read of the SPI data register.
This read/write bit enables the MODF and OVRF bits to generate interrupt requests.
This clearable, read-only flag is set if software does not read the byte in the receive data register before
the next full byte enters the shift register. In an overflow condition, the byte already in the receive data
register is unaffected, and the byte that shifted in last is lost. Clear the OVRF bit by reading the SPI
status and control register with OVRF set and then reading the receive data register.
1 = SPTE interrupt requests enabled
0 = SPTE interrupt requests disabled
1 = Receive data register full
0 = Receive data register not full
1 = MODF and OVRF can generate interrupt requests
0 = MODF and OVRF cannot generate interrupt requests
1 = Overflow
0 = No overflow
Receive data register full
Failure to clear SPRF bit before next byte is received (overflow error)
Inconsistent logic level on SS pin (mode fault error)
Transmit data register empty
Enable error interrupts
Enable mode fault error detection
Select master SPI baud rate
Reset:
Read:
Write:
SPRF
Bit 7
Figure 15-14. SPI Status and Control Register (SPSCR)
0
= Unimplemented
ERRIE
6
0
MC68HC908QB8 Data Sheet, Rev. 3
OVRF
5
0
MODF
0
4
SPTE
3
1
MODFEN
2
0
SPR1
1
0
Freescale Semiconductor
SPR0
Bit 0
0