C8051F016-GQR Silicon Laboratories Inc, C8051F016-GQR Datasheet - Page 160

• Manufacturer Part Number: C8051F016-GQR
• Description: IC 8051 MCU 32K FLASH 48TQFP
• Manufacturer: Silicon Laboratories Inc
• Series: C8051F01xr

Specifications of C8051F016-GQR

• Core Processor: 8051
• Core Size: 8-Bit
• Speed: 25MHz
• Connectivity: SMBus (2-Wire/I²C), SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, Temp Sensor, WDT
• Number Of I /o: 16
• Program Memory Size: 32KB (32K x 8)
• Program Memory Type: FLASH
• Ram Size: 2.25K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b; D/A 2x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 48-TQFP, 48-VQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

20.3.
The system device may implement one or more Programmable Counter Arrays. Following are detailed descriptions
of the special function registers related to the operation of the PCA. The CIP-51 System Controller section of the
datasheet provides additional information on the SFRs and their use.
Bit7:
Bit6:
Bit5:
Bit4:
Bit3:
Bit2:
Bit1:
Bit0:
R/W
Bit7
CF
Register Descriptions for PCA
CF: PCA Counter/Timer Overflow Flag.
Set by hardware when the PCA Counter/Timer overflows from 0xFFFF to 0x0000. When
the Counter/Timer Overflow (CF) interrupt is enabled, setting this bit causes the CPU to
vector to the CF interrupt service routine. This bit is not automatically cleared by
hardware and must be cleared by software.
CR: PCA Counter/Timer Run Control.
This bit enables/disables the PCA Counter/Timer.
0: PCA Counter/Timer disabled.
1: PCA Counter/Timer enabled.
UNUSED. Read = 0, Write = don’t care.
CCF4: PCA Module 4 Capture/Compare Flag.
This bit is set by hardware when a match or capture occurs. When the CCF interrupt is
enabled, setting this bit causes the CPU to vector to the CCF interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
CCF3: PCA Module 3 Capture/Compare Flag.
This bit is set by hardware when a match or capture occurs. When the CCF interrupt is
enabled, setting this bit causes the CPU to vector to the CCF interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
CCF2: PCA Module 2 Capture/Compare Flag.
This bit is set by hardware when a match or capture occurs. When the CCF interrupt is
enabled, setting this bit causes the CPU to vector to the CCF interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
CCF1: PCA Module 1 Capture/Compare Flag.
This bit is set by hardware when a match or capture occurs. When the CCF interrupt is
enabled, setting this bit causes the CPU to vector to the CCF interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
CCF0: PCA Module 0 Capture/Compare Flag.
This bit is set by hardware when a match or capture occurs. When the CCF interrupt is
enabled, setting this bit causes the CPU to vector to the CCF interrupt service routine. This
bit is not automatically cleared by hardware and must be cleared by software.
R/W
Bit6
CR
Figure 20.8. PCA0CN: PCA Control Register
R/W
Bit5
-
CCF4
R/W
Bit4
Rev. 1.7
CCF3
R/W
Bit3
CCF2
R/W
Bit2
C8051F000/1/2/5/6/7
C8051F010/1/2/5/6/7
CCF1
R/W
Bit1
(bit addressable)
CCF0
R/W
Bit0
SFR Address:
Reset Value
00000000
0xD8
160