M30620FCAFP#U5 Renesas Electronics America, M30620FCAFP#U5 Datasheet - Page 24

• Manufacturer Part Number: M30620FCAFP#U5
• Description: IC M16C MCU FLASH 100QFP
• Manufacturer: Renesas Electronics America
• Series: M16C™ M16C/60r

Specifications of M30620FCAFP#U5

• Core Processor: M16C/60
• Core Size: 16-Bit
• Speed: 16MHz
• Connectivity: SIO, UART/USART
• Peripherals: DMA, PWM, WDT
• Number Of I /o: 85
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 10K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 10x10b, D/A 2x8b
• Oscillator Type: Internal
• Operating Temperature: -20°C ~ 85°C
• Package / Case: 100-QFP
• Package: 100PQFP
• Family Name: M16C
• Maximum Speed: 16 MHz
• Operating Supply Voltage: 5 V
• Data Bus Width: 16|32 Bit
• Number Of Programmable I/os: 87
• Interface Type: SIM/UART
• On-chip Adc: 10-chx10-bit
• On-chip Dac: 2-chx8-bit
• Number Of Timers: 11
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Software Reset
Software Reset
Software Reset
Processor Mode
Writing “1” to bit 3 of the processor mode register 0 (address 0004
microcomputer. A software reset has the same effect as a hardware reset. The contents of internal RAM
are preserved.
(1) Types of Processor Mode
(2) Setting Processor Modes
One of three processor modes can be selected: single-chip mode, memory expansion mode, and micro-
processor mode. The functions of some pins, the memory map, and the access space differ according to
the selected processor mode.
The processor mode is set using the CNV
0004
Regardless of the level of the CNV
never change the processor mode bits when changing the contents of other bits. Do not change the
processor mode bits simultaneously with other bits when changing the processor mode bits “01
“11
the microprocessor mode within the program stored in the internal ROM area.
• Single-chip mode
• Memory expansion mode
• Microprocessor mode
• Applying V
• Applying V
In single-chip mode, only internal memory space (SFR, internal RAM, and internal ROM) can be
accessed. However, after the reset has been released and the operation of shifting from the micropro-
cessor mode has started (“H” applied to the CNV
even if the CPU shifts to the single-chip mode.
Ports P0 to P10 can be used as programmable I/O ports or as I/O ports for the internal peripheral
functions.
In memory expansion mode, external memory can be accessed in addition to the internal memory
space (SFR, internal RAM, and internal ROM). However, after the reset has been released and the
operation of shifting from the microprocessor mode has started (“H” applied to the CNV
internal ROM area cannot be accessed even if the CPU shifts to the memory expansion mode.
In this mode, some of the pins function as the address bus, the data bus, and as control signals. The
number of pins assigned to these functions depends on the bus and register settings. (See “Bus
Settings” for details.)
In microprocessor mode, the SFR, internal RAM, and external memory space can be accessed. The
internal ROM area cannot be accessed.
In this mode, some of the pins function as the address bus, the data bus, and as control signals. The
number of pins assigned to these functions depends on the bus width and register settings. (See “Bus
Settings” for details.)
The microcomputer begins operation in single-chip mode after being reset. Memory expansion mode
is selected by writing “01
The microcomputer starts to operate in microprocessor mode after being reset.
2
”. Change the processor mode bits after changing the other bits. Also do not attempt to shift to or from
16
). Do not set the processor mode bits to “10
SS
CC
to CNV
to CNV
SS
SS
2
pin
pin
” to the processor mode bits.
SS
pin, changing the processor mode bits selects the mode. Therefore,
SS
pin and the processor mode bits (bits 1 and 0 at address
2
”.
SS
pin), the internal ROM area cannot be accessed
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
16
) applies a (software) reset to the
M16C / 62A Group
Mitsubishi microcomputers
SS
pin), the
2
” or
21