LPC2114FBD64,151 NXP Semiconductors, LPC2114FBD64,151 Datasheet - Page 17

• Manufacturer Part Number: LPC2114FBD64,151
• Description: IC ARM7 MCU FLASH 128K 64-LQFP
• Manufacturer: NXP Semiconductors
• Series: LPC2100r

Specifications of LPC2114FBD64,151

• Core Processor: ARM7
• Core Size: 16/32-Bit
• Speed: 60MHz
• Connectivity: I²C, Microwire, SPI, SSI, SSP, UART/USART
• Peripherals: POR, PWM, WDT
• Number Of I /o: 46
• Program Memory Size: 128KB (128K x 8)
• Program Memory Type: FLASH
• Ram Size: 16K x 8
• Voltage - Supply (vcc/vdd): 1.65 V ~ 3.6 V
• Data Converters: A/D 4x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-LQFP
• For Use With: MCB2100 - BOARD EVAL NXP LPC211X/LPC212X
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -
• Other names: 568-1222; 935274514151; LPC2114FBD64-S

NXP Semiconductors
LPC2114_2124_6
Product data sheet
6.12.1 Features
6.13.1 Features
6.12 SSP controller (LPC2114/2124/01 only)
6.13 General purpose timers
Remark: This peripheral is available in LPC2114/2124/01 only.
The SSP is a controller capable of operation on a SPI, 4-wire SSI, or Microwire bus. It can
interact with multiple masters and slaves on the bus. Only a single master and a single
slave can communicate on the bus during a given data transfer. Data transfers are in
principle full duplex, with frames of four to 16 bits of data flowing from the master to the
slave and from the slave to the master.
While the SSP and SPI1 peripherals share the same physical pins, it is not possible to
have both of these two peripherals active at the same time. The application can switch on
the fly from SPI1 to SSP and back.
The Timer is designed to count cycles of the peripheral clock (PCLK) and optionally
generate interrupts or perform other actions at specified timer values, based on four
match registers. It also includes four capture inputs to trap the timer value when an input
signal transitions, optionally generating an interrupt. Multiple pins can be selected to
perform a single capture or match function, providing an application with ‘or’ and ‘and’, as
well as ‘broadcast’ functions among them.
•
•
•
•
•
•
•
•
•
Compatible with Motorola’s SPI, Texas Instrument’s 4-wire SSI, and National
Semiconductor’s Microwire buses.
Synchronous serial communication.
Master or slave operation.
8-frame FIFOs for both transmit and receive.
Four to 16 bits per frame.
A 32-bit Timer/Counter with a programmable 32-bit Prescaler.
Four 32-bit capture channels per timer that can take a snapshot of the timer value
when an input signal transitions. A capture event may also optionally generate an
interrupt.
Four 32-bit match registers that allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
Four external outputs per timer corresponding to match registers, with the following
capabilities:
– Set LOW on match.
– Set HIGH on match.
– Toggle on match.
– Do nothing on match.
Rev. 06 — 10 December 2007
Single-chip 16/32-bit microcontrollers
LPC2114/2124
© NXP B.V. 2007. All rights reserved.
17 of 40