LD2985BM50R STMicroelectronics, LD2985BM50R Datasheet - Page 14

• Manufacturer Part Number: LD2985BM50R
• Description: IC REG LDO 5.0V 150MA SOT23-5L
• Manufacturer: STMicroelectronics

Specifications of LD2985BM50R

• Regulator Topology: Positive Fixed
• Voltage - Output: 5V
• Voltage - Input: Up to 16V
• Voltage - Dropout (typical): 0.28V @ 150mA
• Number Of Regulators: 1
• Current - Output: 150mA
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: SOT-23-5, SC-74A, SOT-25
• Number Of Outputs: 1
• Polarity: Positive
• Input Voltage Max: 16 V
• Output Voltage: 5 V
• Output Type: Fixed
• Dropout Voltage (max): 575 mV
• Output Current: 150 mA
• Line Regulation: 0.014 % / V
• Voltage Regulation Accuracy: 2.5 %
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Limit (min): -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 497-3500-2

6
6.1
6.2
6.3
6.4
6.5
14/21
Application notes
External capacitors
Like any low-dropout regulator, the LD2985 requires external capacitors for regulator
stability. This capacitor must be selected to meet the requirements of minimum capacitance
and equivalent series resistance. We suggest to solder input and output capacitors as close
as possible to the relative pins.
Input capacitor
An input capacitor whose value is 1 µF is required with the LD2985 (amount of capacitance
can be increased without limit). This capacitor must be located a distance of not more than
0.5" from the input pin of the device and returned to a clean analog ground. Any good quality
ceramic, tantalum or film capacitors can be used for this capacitor.
Output capacitor
The LD2985 is designed specifically to work with ceramic output capacitors. It may also be
possible to use Tantalum capacitors, but these are not as attractive for reasons of size and
cost. By the way, the output capacitor must meet both the requirement for minimum amount
of capacitance and ESR (equivalent series resistance) value. Due to the different loop gain,
the stability improves for higher output versions and so the suggested minimum output
capacitor value, if low ESR ceramic type is used, is 1 µF for output voltages equal or major
than 3.8 V, 2.2 µF for V
if an output capacitor lower than the suggested one is used, it's possible to make stable the
regulator adding a resistor in series to the capacitor.
Important
The output capacitor must maintain its ESR in the stable region over the full operating
temperature to assure stability. Also, capacitor tolerance and variation with temperature
must be considered to assure the minimum amount of capacitance is provided at all times.
This capacitor should be located not more than 0.5" from the output pin of the device and
returned to a clean analog ground.
Inhibit input operation
The inhibit pin can be used to turn OFF the regulator when pulled low, so drastically
reducing the current consumption down to less than 1 µA. When the inhibit feature is not
used, this pin must be tied to V
proper operation, the signal source used to drive the inhibit pin must be able to swing above
and below the specified thresholds listed in the electrical characteristics section under V
V
IL
. Any slew rate can be used to drive the inhibit.
O
going from 1.8 to 3.3 V, and 3.3 µF for the other versions. However,
I
to keep the regulator output ON at all times. To assure
IH