MCF5282CVM80 Freescale Semiconductor, MCF5282CVM80 Datasheet - Page 279

• Manufacturer Part Number: MCF5282CVM80
• Description: IC MPU 512K 80MHZ 256-MAPBGA
• Manufacturer: Freescale Semiconductor
• Series: MCF528xr

Specifications of MCF5282CVM80

• Core Processor: Coldfire V2
• Core Size: 32-Bit
• Speed: 80MHz
• Connectivity: CAN, EBI/EMI, Ethernet, I²C, SPI, UART/USART
• Peripherals: DMA, LVD, POR, PWM, WDT
• Number Of I /o: 150
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Ram Size: 64K x 8
• Voltage - Supply (vcc/vdd): 2.7 V ~ 3.6 V
• Data Converters: A/D 8x10b
• Oscillator Type: External
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 256-MAPBGA
• Controller Family/series: ColdFire
• Ram Memory Size: 64KB
• Embedded Interface Type: CAN, I2C, SPI, UART
• No. Of Pwm Channels: 8
• Digital Ic Case Style: MAPBGA
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Eeprom Size: -

Freescale Semiconductor
10–8
5–4
2–0
Bit
7
6
3
Name
IMRS Initiate mode register set (
CBM Command and bank MUX [2:0]. Because different SDRAM configurations cause the command and
PS
—
IP
—
bank select lines to correspond to different addresses, these resources are programmable. CBM
determines the addresses onto which these functions are multiplexed.
Note: It is important to set CBM according to the location of the command bit.
This encoding and the address multiplexing scheme handle common SDRAM organizations. Bank
select bits include a base bit and all address bits above for SDRAMs with multiple bank select bits.
Reserved, should be cleared.
SDRAMs. In initialization, IMRS should be set only after all DRAM controller registers are initialized
and
block programs the SDRAM’s mode register. Thus, the address of the access should be programmed
to place the correct mode information on the SDRAM address pins. Because the SDRAM does not
register this information, it doesn’t matter if the IMRS access is a read or a write or what, if any, data is
put onto the data bus. The DRAM controller clears IMRS after the
0 Take no action
1 Initiate
Port size. Indicates the port size of the associated block of SDRAM, which allows for dynamic sizing of
associated SDRAM accesses. PS functions the same in asynchronous operation.
00 32-bit port
01 8-bit port
1x 16-bit port
Initiate precharge all (
finished. Accesses via IP should be no wider than the port size programmed in PS.
0 Take no action.
1 A
Reserved, should be cleared.
executed after all DRAM controller registers are programmed. After IP is set, the next write to an
appropriate SDRAM address generates the
PALL
PALL
MCF5282 and MCF5216 ColdFire Microcontroller User’s Manual, Rev. 3
and
MRS
command is sent to the associated SDRAM block. During initialization, this command is
Table 15-5. DACRn Field Descriptions (continued)
REFRESH
command
PALL
commands have been issued. After IMRS is set, the next access to an SDRAM
MRS
) command. The DRAM controller clears IP after the
CBM
101
110
111
000
001
010
011
100
) command. Setting IMRS generates a
Command Bit
Description
PALL
17
18
19
20
21
22
23
24
command to the SDRAM block.
Bank Select Bits
18 and up
19 and up
20 and up
21 and up
22 and up
23 and up
24 and up
25 and up
MRS
Synchronous DRAM Controller Module
MRS
command finishes.
command to the associated
PALL
command is
15-7