SC16C752BIB48,151 NXP Semiconductors, SC16C752BIB48,151 Datasheet - Page 8

• Manufacturer Part Number: SC16C752BIB48,151
• Description: IC DUAL UART 64BYTE 48LQFP
• Manufacturer: NXP Semiconductors

Specifications of SC16C752BIB48,151

• Number Of Channels: 2, DUART
• Package / Case: 48-LFQFP
• Fifo's: 64 Byte
• Voltage - Supply: 2.5V, 3.3V, 5V
• With Auto Flow Control: Yes
• With False Start Bit Detection: Yes
• With Modem Control: Yes
• Mounting Type: Surface Mount
• Voltage: 2.25 V ~ 5.5 V
• Data Rate: 5 Mbps
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.25 V
• Supply Current: 4.5 mA
• Maximum Operating Temperature: + 85 C
• Minimum Operating Temperature: - 40 C
• Mounting Style: SMD/SMT
• Operating Supply Voltage: 2.5 V or 3.3 V or 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Features: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: 935274411151; SC16C752BIB48-S; SC16C752BIB48-S

NXP Semiconductors
SC16C752B
Product data sheet
Fig 4.
Fig 5.
D7 to D0
Auto flow control (auto-RTS and auto-CTS) example
N = receiver FIFO trigger level.
The two blocks in dashed lines cover the case where an additional byte is sent, as described in
RTS functional timing
RTSn
RXn
IOR
6.2.1 Auto-RTS
Start
Auto-RTS data flow control originates in the receiver block (see
on page
in auto-RTS are stored in the TCR. RTSn is active if the RX FIFO level is below the halt
trigger level in TCR[3:0]. When the receiver FIFO halt trigger level is reached, RTSn is
de-asserted. The sending device (e.g., another UART) may send an additional byte after
the trigger level is reached (assuming the sending UART has another byte to send)
because it may not recognize the de-assertion of RTSn until it has begun sending the
additional byte. RTSn is automatically reasserted once the receiver FIFO reaches the
resume trigger level programmed via TCR[7:4]. This re-assertion allows the sending
device to resume transmission.
FIFO
FIFO
TX
RX
UART 1
byte N
3).
SERIAL TO
TO SERIAL
PARALLEL
PARALLEL
CONTROL
CONTROL
Figure 5
FLOW
FLOW
Stop
All information provided in this document is subject to legal disclaimers.
5 V, 2.2 V and 2.5 V dual UART, 5 Mbit/s (max.), with 64-byte FIFOs
shows RTSn functional timing. The receiver FIFO trigger levels used
Rev. 6 — 30 November 2010
RTSn
CTSn
Start
RXn
TXn
byte N + 1
1
TXn
CTSn
RXn
RTSn
2
Stop
SERIAL TO
TO SERIAL
PARALLEL
PARALLEL
CONTROL
CONTROL
FLOW
FLOW
UART 2
N
FIFO
FIFO
Section
Figure 1 “Block diagram”
SC16C752B
RX
TX
N+1
6.2.1.
002aaf905
© NXP B.V. 2010. All rights reserved.
Start
002aaf906
D7 to D0
8 of 47