T48C862M-R4-TNQ Atmel, T48C862M-R4-TNQ Datasheet - Page 13

• Manufacturer Part Number: T48C862M-R4-TNQ
• Description: IC MON TIRE PRESS 433MHZ 24-SOIC
• Manufacturer: Atmel

Specifications of T48C862M-R4-TNQ

• Frequency: 433MHz
• Modulation Or Protocol: FM, FSK
• Data Rate - Maximum: 32 kBaud
• Power - Output: 10dBm
• Current - Transmitting: 9.5mA
• Data Interface: PCB, Surface Mount
• Antenna Connector: PCB, Surface Mount
• Memory Size: 1KB EEPROM, 1KB RAM
• Voltage - Supply: 2 V ~ 4 V
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 24-SOIC (0.200", 5.30mm Width)
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Features: -
• Applications: -

Microcontroller Block
Features
Description
Introduction
Differences between T48C862-R4 and ATAR862 Microcontrollers
Program Memory
Configuration Memory
Data Memory
4551C–4BMCU–01/04
•
•
•
•
•
•
•
•
•
•
•
•
•
•
The microcontroller is designed with EEPROM cells so it can be programmed several
times. To offer full compatibility with each ROM version, the I/O configuration is stored
into a separate internal EEPROM block during programming. The configuration is down-
loaded to the I/Os with every power-on reset.
The microcontroller block is a member of Atmel’s family of 4-bit single-chip microcontrol-
lers. Instead of ROM it contains EEPROM, RAM, parallel I/O ports, two 8-bit
programmable multifunction timer/counters, voltage supervisor, interval timer with
watchdog function and a sophisticated on-chip clock generation with integrated RC-,
32-kHz and 4-MHz crystal oscillators.
The program memory of the devices is realized as an EEPROM. The memory size for
user programs is 4096 bytes. It is programmed as 258
implement LOCK-bit function is user-selectable and protects the device from unautho-
rized read-out of the program memory.
An additional area of 32 bytes of the EEPROM is used to store information about the
hardware configuration. All the options that are selectable for the ROM versions are
available to the user. This includes not only the different port options but also the possi-
bilities to select different capacitors for OSC1 and OSC2, the option to enable or disable
the hardlock for the watchdog, the option to select OSC2 instead of OSC1 as external
clock input and the option to enable the external clock monitor as a reset source.
The microcontroller block contains an internal data EEPROM that is organized as two
pages of 32
defined within the application software by writing the 2-wire interface (TWI) command
"09h" to the EEPROM. This command has no effect for the microcontroller block, if it is
left inside the HEX-file for the ROM version. Also for compatibility reasons, the access to
the EEPROM is handled via the MCL (serial interface) as in the corresponding ROM
parts.
4-Kbyte ROM, 256 x 4-bit RAM
EEPROM Programmable Options
Read Protection for the EEPROM Program Memory
11 Bi-directional I/Os
Up to Seven External/Internal Interrupt Sources
Eight Hardware and Software Interrupt Priorities
Multifunction Timer/Counter
- IR Remote Control Carrier Generator
- Biphase-, Manchester- and Pulse-width Modulator and Demodulator
- Phase Control Function
Programmable System Clock with Prescaler and Five Different Clock Sources
Very Low Sleep Current (< 1 µA)
2
256
Synchronous Serial Interface (2-wire, 3-wire)
Watchdog, POR and Brown-out Function
Voltage Monitoring Inclusive Lo_BAT Detect
512-bit EEPROM Data Memory
4-bit RAM Data Memory
16-bit. To be compatible with the ROM parts, the page used has to be
T48C862-R4 [Preliminary]
16 bytes blocks of data. the
13