ISL62883HRTZ Intersil, ISL62883HRTZ Datasheet - Page 12

• Manufacturer Part Number: ISL62883HRTZ
• Description: IC REG PWM 3PHASE BUCK 40TQFN
• Manufacturer: Intersil

Specifications of ISL62883HRTZ

• Applications: Controller, Intel IMVP-6.5™
• Voltage - Input: 5 V ~ 21 V
• Number Of Outputs: 1
• Voltage - Output: 0.0125 V ~ 1.5 V
• Operating Temperature: -10°C ~ 100°C
• Mounting Type: *
• Package / Case: *
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Each slave circuit has its own ripple capacitor C
voltage mimics the inductor ripple current. A g
amplifier converts the inductor voltage into a current
source to charge and discharge C
turns on its PWM pulse upon receiving the clock signal,
and the current source charges C
V
and the current source discharges C
Since the ISL62883 works with V
amplitude and noise-free synthesized signals, the
ISL62883 achieves lower phase jitter than conventional
hysteretic mode and fixed PWM mode controllers. Unlike
conventional hysteretic mode converters, the ISL62883
has an error amplifier that allows the controller to
maintain a 0.5% output voltage accuracy.
Figure 5 shows the operation principles during load
insertion response. The COMP voltage rises during load
insertion, generating the master clock signal more
quickly, so the PWM pulses turn on earlier, increasing the
effective switching frequency, which allows for higher
control loop bandwidth than conventional fixed frequency
PWM controllers. The VW voltage rises as the COMP
voltage rises, making the PWM pulses wider. During load
release response, the COMP voltage falls. It takes the
master clock circuit longer to generate the next master
clock signal so the PWM pulse is held off until needed.
The VW voltage falls as the VW voltage falls, reducing the
current PWM pulse width. This kind of behavior gives the
ISL62883 excellent response speed.
The fact that all the phases share the same VW window
voltage also ensures excellent dynamic current balance
among phases.
Diode Emulation and Period Stretching
ISL62883 can operate in diode emulation (DE) mode to
improve light load efficiency. In DE mode, the low-side
MOSFET conducts when the current is flowing from
source to drain and doesn’t not allow reverse current,
emulating a diode. As Figure 6 shows, when LGATE is
on, the low-side MOSFET carries current, creating
negative voltage on the phase node due to the voltage
drop across the ON-resistance. The ISL62883 monitors
the current through monitoring the phase node voltage.
It turns off LGATE when the phase node voltage reaches
U G A T E
L G A T E
Crs
P h a s e
hits VW, the slave circuit turns off the PWM pulse,
IL
FIGURE 6. DIODE EMULATION
12
crs
rs
rs
. When C
. The slave circuit
, which are large-
rs
.
ISL62883, ISL62883B
rs
m
voltage
rs
, whose
zero to prevent the inductor current from reversing the
direction and creating unnecessary power loss.
If the load current is light enough, as Figure 6 shows, the
inductor current will reach and stay at zero before the
next phase node pulse, and the regulator is in
discontinuous conduction mode (DCM). If the load
current is heavy enough, the inductor current will never
reach 0A, and the regulator is in CCM although the
controller is in DE mode.
Figure 7 shows the operation principle in diode
emulation mode at light load. The load gets
incrementally lighter in the three cases from top to
bottom. The PWM on-time is determined by the VW
window size, therefore is the same, making the inductor
current triangle the same in the three cases. The
ISL62883 clamps the ripple capacitor voltage V
mode to make it mimic the inductor current. It takes
the COMP voltage longer to hit V
the switching period. The inductor current triangles
move further apart from each other such that the
inductor current average value is equal to the load
current. The reduced switching frequency helps increase
light load efficiency.
Start-up Timing
With the controller's V
threshold, the start-up sequence begins when VR_ON
exceeds the 3.3V logic high threshold. The ISL62883
uses digital soft start to ramp up DAC to the boot voltage
of 1.1V at about 2.5mV/µs. Once the output voltage is
within 10% of the boot voltage for 13 PWM cycles (43µs
for frequency = 300kHz), CLK_EN# is pulled low and
DAC slews at 5mV/µs to the voltage set by the VID pins.
PGOOD is asserted high in approximately 7ms. Figure 8
shows the typical start-up timing. Similar results occur if
Vcrs
Vcrs
Vcrs
iL
iL
iL
FIGURE 7. PERIOD STRETCHING
CCM/DCM BOUNDARY
VW
VW
VW
DD
LIGHT DCM
DEEP DCM
voltage above the POR
crs
, naturally stretching
crs
FN6891.3
in DE