SC16C2552BIA44 NXP Semiconductors, SC16C2552BIA44 Datasheet - Page 19

• Manufacturer Part Number: SC16C2552BIA44
• Description: UART, 2 CH, 16BYTE FIFO, 16C2552
• Manufacturer: NXP Semiconductors

Specifications of SC16C2552BIA44

• No. Of Channels: 2
• Data Rate: 5Mbps
• Supply Voltage Range: 2.25V To 5.5V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: PLCC
• No. Of Pins: 44
• Svhc: No SVHC (18-Jun-2010)
• Operating: RoHS Compliant
• Uart Features: Independent Transmit & Receive UART Control, Multi-Function Output, Modem Control Functions
• Rohs Compliant: Yes

NXP Semiconductors
SC16C2552B_3
Product data sheet
7.7 Line Status Register (LSR)
This register provides the status of data transfers between the SC16C2552B and
the CPU.
Table 17.
Bit
7
6
5
4
3
2
1
0
Symbol
LSR[7]
LSR[6]
LSR[5]
LSR[4]
LSR[3]
LSR[2]
LSR[1]
LSR[0]
Line Status Register bits description
Description
FIFO data error.
THR and TSR empty. This bit is the Transmit Empty indicator. This bit is set to a
logic 1 whenever the Transmit Holding Register and the Transmit Shift Register
are both empty. It is reset to logic 0 whenever either the THR or TSR contains a
data character. In the FIFO mode, this bit is set to logic 1 whenever the Transmit
FIFO and Transmit Shift Register are both empty.
THR empty. This bit is the Transmit Holding Register Empty indicator. This bit
indicates that the UART is ready to accept a new character for transmission. In
addition, this bit causes the UART to issue an interrupt to CPU when the THR
interrupt enable is set. The THR bit is set to a logic 1 when a character is
transferred from the Transmit Holding Register into the Transmit Shift Register.
The bit is reset to a logic 0 concurrently with the loading of the Transmit Holding
Register by the CPU. In the FIFO mode, this bit is set when the transmit FIFO is
empty; it is cleared when at least 1 byte is written to the transmit FIFO.
Break interrupt.
Framing error.
Parity error.
Overrun error.
Receive data ready.
logic 0 = no error (normal default condition)
logic 1 = at least one parity error, framing error or break indication is in the
current FIFO data. This bit is cleared when RHR register is read.
logic 0 = no break condition (normal default condition)
logic 1 = the receiver received a break signal (RX was a logic 0 for one
character frame time). In the FIFO mode, only one break character is loaded
into the FIFO.
logic 0 = no framing error (normal default condition)
logic 1 = framing error. The receive character did not have a valid stop bit(s). In
the FIFO mode, this error is associated with the character at the top of the
FIFO.
logic 0 = no parity error (normal default condition
logic 1 = parity error. The receive character does not have correct parity
information and is suspect. In the FIFO mode, this error is associated with the
character at the top of the FIFO.
logic 0 = no overrun error (normal default condition)
logic 1 = overrun error. A data overrun error occurred in the Receive Shift
Register. This happens when additional data arrives while the FIFO is full. In
this case, the previous data in the shift register is overwritten. Note that under
this condition, the data byte in the Receive Shift Register is not transferred into
the FIFO, therefore the data in the FIFO is not corrupted by the error.
logic 0 = no data in Receive Holding Register or FIFO (normal default
condition)
logic 1 = data has been received and is saved in the Receive Holding Register
or FIFO
5 V, 3.3 V and 2.5 V dual UART, 5 Mbit/s (max.), with 16-byte FIFOs
Rev. 03 — 12 February 2009
SC16C2552B
© NXP B.V. 2009. All rights reserved.
19 of 38