DSPIC30F3013-20I/ML Microchip Technology, DSPIC30F3013-20I/ML Datasheet - Page 23

• Manufacturer Part Number: DSPIC30F3013-20I/ML
• Description: IC,DSP,16-BIT,CMOS,LLCC,44PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: dsPIC™ 30Fr

Specifications of DSPIC30F3013-20I/ML

• Rohs Compliant: YES
• Core Processor: dsPIC
• Core Size: 16-Bit
• Speed: 20 MIPS
• Connectivity: I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, POR, PWM, WDT
• Number Of I /o: 20
• Program Memory Size: 24KB (8K x 24)
• Program Memory Type: FLASH
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 2.5 V ~ 5.5 V
• Data Converters: A/D 10x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Package: 44QFN EP
• Device Core: dsPIC
• Family Name: dsPIC30
• Maximum Speed: 20 MHz
• Operating Supply Voltage: 3.3|5 V
• Data Bus Width: 16 Bit
• Number Of Programmable I/os: 30
• Interface Type: I2C/SPI/UART
• On-chip Adc: 10-chx12-bit
• Number Of Timers: 3
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: DV164033 - KIT START EXPLORER 16 MPLAB ICD2DM240001 - BOARD DEMO PIC24/DSPIC33/PIC32
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: DSPIC30F301320IML

2.4
The DSP engine consists of a high-speed 17-bit x
17-bit multiplier, a barrel shifter and a 40-bit
adder/subtracter (with two target accumulators, round
and saturation logic).
The DSP engine also has the capability to perform
inherent
which require no additional data. These instructions are
ADD, SUB and NEG.
The dsPIC30F is a single-cycle instruction flow
architecture, therefore, concurrent operation of the
DSP engine with MCU instruction flow is not possible.
However, some MCU ALU and DSP engine resources
may be used concurrently by the same instruction
(e.g., ED, EDAC). See
TABLE 2-2:
© 2010 Microchip Technology Inc.
Instruction
MOVSAC
MPY.N
EDAC
CLR
MAC
MAC
MPY
MSC
ED
DSP Engine
accumulator-to-accumulator
DSP INSTRUCTION
SUMMARY
No change in A
A = A + (x – y)
A = A + (x * y)
A = A – x • y
A = (x – y)
Operation
Algebraic
A = A + x
A = – x • y
A = x • y
Table
A = 0
2-2.
2
2
2
dsPIC30F2011/2012/3012/3013
ACC WB?
operations,
Yes
Yes
Yes
Yes
No
No
No
No
No
The DSP engine has several options selected through
various bits in the CPU Core Configuration register
(CORCON), which are:
1.
2.
3.
4.
5.
6.
7.
A block diagram of the DSP engine is shown in
Figure
Note:
Fractional or integer DSP multiply (IF).
Signed or unsigned DSP multiply (US).
Conventional or convergent rounding (RND).
Automatic saturation on/off for ACCA (SATA).
Automatic saturation on/off for ACCB (SATB).
Automatic saturation on/off for writes to data
memory (SATDW).
Accumulator
(ACCSAT).
2-2.
For CORCON layout, see
Saturation
mode
DS70139G-page 23
Table
selection
3-3.