PIC18F4580-I/ML Microchip Technology, PIC18F4580-I/ML Datasheet - Page 252

• Manufacturer Part Number: PIC18F4580-I/ML
• Description: IC,MICROCONTROLLER,8-BIT,PIC CPU,CMOS,LLCC,44PIN,PLASTIC
• Manufacturer: Microchip Technology
• Series: PIC® 18Fr

Specifications of PIC18F4580-I/ML

• Rohs Compliant: YES
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 40MHz
• Connectivity: CAN, I²C, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, HLVD, POR, PWM, WDT
• Number Of I /o: 36
• Program Memory Size: 32KB (16K x 16)
• Program Memory Type: FLASH
• Eeprom Size: 256 x 8
• Ram Size: 1.5K x 8
• Voltage - Supply (vcc/vdd): 4.2 V ~ 5.5 V
• Data Converters: A/D 11x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 44-QFN
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: XLT44QFN2 - SOCKET TRAN ICE 44QFN/40DIPAC164322 - MODULE SOCKET MPLAB PM3 28/44QFN444-1001 - DEMO BOARD FOR PICMICRO MCU
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

PIC18F2480/2580/4480/4580
19.4.2
The operation of the Synchronous Master and Slave
modes is identical, except in the case of Sleep or any
Idle mode and bit, SREN, which is a “don’t care” in
Slave mode.
If receive is enabled by setting the CREN bit prior to
entering Sleep or any Idle mode, then a word may be
received while in this low-power mode. Once the word
is received, the RSR register will transfer the data to the
RCREG register. If the RCIE enable bit is set, the inter-
rupt generated will wake the chip from the low-power
mode. If the global interrupt is enabled, the program will
branch to the interrupt vector.
TABLE 19-10: REGISTERS ASSOCIATED WITH SYNCHRONOUS SLAVE RECEPTION
DS39637D-page 252
INTCON
PIR1
PIE1
IPR1
RCSTA
RCREG
TXSTA
BAUDCON
SPBRGH
SPBRG
Legend: — = unimplemented, read as ‘0’. Shaded cells are not used for synchronous slave reception.
Note 1:
Name
Reserved in PIC18F2X80 devices; always maintain these bits clear.
EUSART SYNCHRONOUS SLAVE
RECEPTION
EUSART Receive Register
EUSART Baud Rate Generator Register High Byte
EUSART Baud Rate Generator Register Low Byte
GIE/GIEH PEIE/GIEL TMR0IE
ABDOVF
PSPIF
PSPIE
PSPIP
CSRC
SPEN
Bit 7
(1)
(1)
(1)
RCIDL
ADIE
ADIP
ADIF
Bit 6
RX9
TX9
SREN
TXEN
RCIF
RCIE
RCIP
Bit 5
—
INT0IE
CREN
SYNC
SCKP
Bit 4
TXIF
TXIE
TXIP
ADDEN
SENDB
BRG16
SSPIE
SSPIP
To set up a Synchronous Slave Reception:
1.
2.
3.
4.
5.
6.
7.
8.
9.
SSPIF
RBIE
Bit 3
Enable the synchronous master serial port by
setting bits, SYNC and SPEN, and clearing bit,
CSRC.
If interrupts are desired, set enable bit, RCIE.
If 9-bit reception is desired, set bit, RX9.
To enable reception, set enable bit, CREN.
Flag bit, RCIF, will be set when reception is
complete. An interrupt will be generated if
enable bit, RCIE, was set.
Read the RCSTA register to get the 9th bit (if
enabled) and determine if any error occurred
during reception.
Read the 8-bit received data by reading the
RCREG register.
If any error occurred, clear the error by clearing
bit, CREN.
If using interrupts, ensure that the GIE and PEIE
bits in the INTCON register (INTCON<7:6>) are
set.
TMR0IF
CCP1IE
CCP1IP
CCP1IF
BRGH
FERR
Bit 2
—
TMR2IF
TMR2IE
TMR2IP
INT0IF
OERR
TRMT
WUE
© 2009 Microchip Technology Inc.
Bit 1
TMR1IF
TMR1IE
TMR1IP
ABDEN
RX9D
TX9D
RBIF
Bit 0
on Page:
Values
Reset
55
58
58
58
57
57
57
57
57
57