ISL29011IROZ-T7 Intersil, ISL29011IROZ-T7 Datasheet
ISL29011IROZ-T7
Specifications of ISL29011IROZ-T7
Available stocks
Related parts for ISL29011IROZ-T7
ISL29011IROZ-T7 Summary of contents
Page 1
... CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. | 1-888-INTERSIL or 1-888-468-3774 Intersil (and design registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2009, 2010. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. ...
Page 2
... Ordering Information PART NUMBER (Notes ISL29011IROZ-T7 ISL29011IROZ-EVALZ NOTES: 1. Please refer to TB347 for details on reel specifications. 2. These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and NiPdAu plate - e4 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020 ...
Page 3
Block Diagram PHOTODIODE ARRAY LIGHT DATA PROCESS ALS AND IR IR PHOTODIODE ARRAY 4 REXT 3 ISL29011 VDDA 2 INTEGRATION ADC IREF FOSC 3 GND ISL29011 VDDD 1 COMMAND REGISTER DATA REGISTER SDA SCL 5 INTERRUPT ...
Page 4
... Thermal Resistance (Typical, Note 4) DD +/- 0. ODFN . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . DDD Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . +90°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +100°C + 0.5V Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85° 0.5V Pb-Free Reflow Profile .see link below DD http://www.intersil.com/pbfree/Pb-FreeReflow.asp = 3V +25° 499kΩ 1% tolerance, 16-bit ADC operation, unless otherwise A EXT ,V ) ...
Page 5
Electrical Specifications V SUP(V (Continued) PARAMETER DESCRIPTION V Voltage Head Room of IRDR Pin IRLED t Rise Time for IRDR Source Current r t Fall Time for IRDR Source Current LED Modulation Frequency IRLED1 f IR LED ...
Page 6
I2C Electrical Specifications For SCL and SDA unless otherwise noted, V 16-bit ADC operation (Note 9). PARAMETER DESCRIPTION t Set-up Time for STOP Condition SU:STO t Bus Free Time Between a STOP and START BUF Condition C Capacitive Load for ...
Page 7
ADC can be configured at its lowest range (Range 1) in the ambient light sensing. For very bright conditions, the ADC can be configured at its highest range (Range 4) in the proximity sensing. Low-Power Operation The ISL29011 ...
Page 8
START DEVICE ADDRESS DATA SDA SDA SDA DRIVEN BY MASTER OUT CLK ...
Page 9
Once triggered, INT pin stays low and the status bit stays high. Both interrupt pin and the status bit are automatically cleared at the end of Command Register I transfer. TABLE 3. INTERRUPT FLAG BIT 2 OPERATION 0 Interrupt is ...
Page 10
Registers 06 and 07 hex set the high (HI) threshold for the interrupt pin and the interrupt flag. 06 hex is the LSB and 07 hex is the MSB. By default, the Interrupt threshold hex for both ...
Page 11
... Upon power-up, please ensure a VDD slew rate of 0.5V/ms or greater. After power-up the user’s power supply temporarily deviates from our specification (2.25V to 3.63V), Intersil recommends the user write 0x00 to two registers: 0x08, 0x00 (in that order), wait ~1ms or more and then rewrite all registers as desired. ...
Page 12
The device can be tied onto a system’ together with other I C compliant devices. Soldering Considerations Convection heating is recommended for reflow soldering; direct-infrared heating is not recommended. The plastic ODFN package does not require a ...
Page 13
Typical Performance Curves 1.2 SUN 1.0 0.8 0.6 0.4 0.2 0 300 400 500 600 700 800 WAVELENGTH (nm) FIGURE 6. SPECTRUM OF FOUR LIGHT SOURCES RADIATION PATTERN 0° 10° 10° 20° LUMINOSITY 30° ANGLE 40° 50° 60° 70° 80° ...
Page 14
Typical Performance Curves 350 300 PIG'S SKIN 250 4mm CENTER-TO-CENTER FOR ISL29011 AND SFH4650, 200 ISOLATED BY BARRIER 150 IR TRANSMITTING GLASS 18% GRAY 130 CTS = 500 CTS x 65% x 65% 100 = 211 CTS BLOND HAIR 50 ...
Page 15
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...
Page 16
Package Outline Drawing L8.2.1x2.0 8 LEAD OPTICAL DUAL FLAT NO-LEAD PLASTIC PACKAGE (ODFN) Rev 1, 12/09 2.10 6 PIN 1 INDEX AREA (2X) 0.10 TOP VIEW 2.50 2.10 (6x0.50) (8x0.20) (8x0.55) (0.75) TYPICAL RECOMMENDED LAND PATTERN 16 ISL29011 A B ...