SPC5604PGF0MLQ6 Freescale Semiconductor, SPC5604PGF0MLQ6 Datasheet - Page 48

• Manufacturer Part Number: SPC5604PGF0MLQ6
• Description: IC MCU 32BIT 512KB FLASH 144LQFP
• Manufacturer: Freescale Semiconductor
• Series: MPC56xx Qorivvar

Specifications of SPC5604PGF0MLQ6

• Core Processor: e200z0h
• Core Size: 32-Bit
• Speed: 64MHz
• Connectivity: CAN, FlexRay, LIN, SPI, UART/USART
• Peripherals: DMA, POR, PWM, WDT
• Number Of I /o: 108
• Program Memory Size: 512KB (512K x 8)
• Program Memory Type: FLASH
• Eeprom Size: 64K x 8
• Ram Size: 40K x 8
• Voltage - Supply (vcc/vdd): 3 V ~ 5.5 V
• Data Converters: A/D 30x10b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 125°C
• Package / Case: 144-LQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

3.6
3.7
3.8
3.8.1
The internal voltage regulator requires an external NPN (BCP56, BCP68, BCX68 or BC817) ballast to be connected as shown
in
be taken to limit the serial inductance of the board to less than 5 nH.
For the MPC5604P microcontroller, 10 µF should be placed between each of the three V
and also between the V
V
V
48
DD_HV_REG
DD
Figure 8
1
2
= 3.0 V to 3.6 V / 4.5 V to 5.5 V, T
Symbol
V
All ESD testing is in conformity with CDF-AEC-Q100 Stress Test Qualification for Automotive Grade Integrated
Circuits.
A device will be defined as a failure if after exposure to ESD pulses the device no longer meets the device
specification requirements. Complete DC parametric and functional testing shall be performed per applicable
device specification at room temperature followed by hot temperature, unless specified otherwise in the device
specification.
EME
V
V
ESD(HBM)
ESD(CDM)
and
Electromagnetic interference (EMI) characteristics
Electrostatic discharge (ESD) characteristics
Power management electrical characteristics
Symbol
/V
Voltage regulator electrical characteristics
Radiated emissions Device configuration, test
Figure
SS_HV_REG
The voltage regulator output cannot be used to drive external circuits. Output pins are to be
used only for decoupling capacitance.
V
not possible to provide V
DD_LV_COR
Parameter
9. Capacitances should be placed on the board as near as possible to the associated pins. Care should also
DD_LV_REGCOR
SR Electrostatic discharge (Human Body Model)
SR Electrostatic discharge (Charged Device Model)
pins.
must be generated using internal regulator and external NPN transistor. It is
conditions and EM testing per
standard IEC61967-2
Supply voltage = 5 V DC
Ambient temperature = 25 °C
Worst-case orientation
/V
MPC5604P Microcontroller Data Sheet, Rev. 7
A
SS_LV_REGCOR
Table 12. EMI testing specifications
= –40 to 125 °C, unless otherwise specified.
DD_LV_COR
Conditions
Parameter
Table 13. ESD ratings
through external regulator.
pair. Additionally, 40 µF should be placed between the
NOTE
f
f
No PLL frequency
modulation
f
f
1% PLL frequency
modulation
OSC
CPU
OSC
CPU
8 MHz
64 MHz
8 MHz
64 MHz
Clocks
1,2
Conditions
—
—
DD_LV_CORx
150 kHz–150 MHz
150 kHz–150 MHz
150–1000 MHz
150–1000 MHz
Frequency
IEC Level
IEC Level
750 (corners)
/V
500 (other)
Freescale Semiconductor
SS_LV_CORx
Value
2000
Level
(Max)
16
15
15
14
M
M
supply pairs
dBµV
dBµV
Unit
Unit
—
—
V
V