CQM1-CIF01 Omron, CQM1-CIF01 Datasheet - Page 71

• Manufacturer Part Number: CQM1-CIF01
• Description: PERIPHERAL CABLE FOR NEC COMP.
• Manufacturer: Omron

Specifications of CQM1-CIF01

• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

50
Speeds (X/Y/Z/U Axes: #0
to #99)
Acceleration/Deceleration
(X/Y/Z/U Axes: #1 to #9)
Dwell Time (X/Y/Z/U Axes:
#1 to #19)
Overview
Notes
Notes
Note Settings can be entered and displayed in either hexadecimal or decimal for-
Note Settings can be entered and displayed in either hexadecimal or decimal for-
1. These values can be entered and displayed in either hexadecimal or dec-
2. Ranges given in the table are for when the displayed value’s unit is set to
Only the X-axis settings are used for the CS1W-NC113/133 and CJ1W-
NC113/133, and only the X- and Y-axis settings are used for the CS1W-
NC213/233 and CJ1W-NC213/233. Settings can be entered and displayed in
either hexadecimal or decimal format depending on the setting of the display
format.
1. Settings can be entered and displayed in either hexadecimal or decimal
2. When the displayed value’s set unit is Pulse. When the set unit is mm or
3. The speeds set above can be set as interpolation speeds. However, make
Only the X-axis settings are used for the CS1W-NC113/133 and CJ1W-
NC113/133, and only the X- and Y-axis settings are used for the CS1W-
NC213/233 and CJ1W-NC213/233. Settings can be entered and displayed in
either hexadecimal or decimal format depending on the setting of the display
format.
mat depending on the setting of the display format.
Only the X-axis settings are used for the CS1W-NC113/133 and CJ1W-
NC113/133, and only the X- and Y-axis settings are used for the CS1W-
NC213/233 and CJ1W-NC213/233. Settings can be entered and displayed in
either hexadecimal or decimal format depending on the setting of the display
format.
mat depending on the setting of the display format.
Acceleration (See note.) 00000000 to 0003D090 Hex (0 to 250,000) (ms)
Deceleration (See note.) 00000000 to 0003D090 Hex (0 to 250,000) (ms)
Dwell time (See note.)
Accel. #
(See note 1.)
Decel. #
(See note 1.)
Start speed
(See note 1.)
Target speed
(See note 1.)
Speed (See notes 1 and 2.)
imal format by setting the display format.
Pulse. When the set unit is millimeters or inches and the pulse rate is set
to a value other than 1, the values displayed will change to the specified
set value × the pulse rate.
format depending on the setting of the display format.
inches and the pulse rate is set to other than 1, the value displayed will
change.
sure that the maximum speed of individual axes does not exceed
500,000 (pps) or the maximum speed set in the parameter settings.
Item
Item
Item
Item
0 to 9 Hex (0 to 9)
0 to 9 Hex (0 to 9)
00 to 63 Hex (0 to 99)
00 to 63 Hex (0 to 99)
0000 to 03E7 Hex (0.00 to 9.99) (s)
00000000 to 000F4240 Hex (0 to 1,000,000) (pps)
Setting range
Setting range
Setting range
Setting range
Section 4-1