GRM21BR71H104KA01L Murata, GRM21BR71H104KA01L Datasheet - Page 86

• Manufacturer Part Number: GRM21BR71H104KA01L
• Description: CAPACITOR, 0805 100NF 50V CAPACITOR, 0805 100NF 50V
• Manufacturer: Murata
• Series: GRM21r

Specifications of GRM21BR71H104KA01L

• Tolerance (+ Or -): 10%
• Voltage: 50VDC
• Temp Coeff (dielectric): X7R
• Operating Temp Range: -55C to 125C
• Mounting Style: Surface Mount
• Construction: SMT Chip
• Case Style: Ceramic Chip
• Failure Rate: Not Required
• Wire Form: Not Required
• Product Length (mm): 2mm
• Product Depth (mm): 1.25mm
• Product Height (mm): 1.25mm
• Product Diameter (mm): Not Requiredmm
• Capacitance: .1uF
• Package / Case: 0805
• Voltage Rating, Dc: 50V
• Capacitor Dielectric Type: CERAMIC MULTI-LAYER
• Tolerance,: 10%
• Tolerance, -: 10%
• Temp, Op. Max: 125(DEGREE C)
• Temp,: ROHS COMPLIANT
• Lead Free Status / RoHS Status: Compliant

!Note
• This PDF catalog is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our
• This PDF catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
sales representatives or product engineers before ordering.
!Note
!Note
84
No.
14
15
16
17
LLL/LLA/LLM Series Specifications and Test Methods (1)
LLL/LLR/LLA/LLM Series Specifications and Test Methods (1)
Continued from the preceding page.
Temperature
Cycle
Humidity
(Steady
Humidity
Load
High
Temperature
Load
State)
1. This Specifications and Test Methods is downloaded from the website of Murata Manufacturing co.,ltd. Therefore, it's specifications are subject to change or our products in it may be discontinued without advance notice.
• Please read rating and !CAUTION (for storage, operating, rating, soldering, mounting and handling) in this catalog to prevent smoking and/or burning, etc.
0.
• This catalog has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering.
2. This Specifications and Test Methods has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product
0.
Please check with our sales representatives or product engineers before ordering.
specifications before ordering.
Item
Appearance No marking defects
Capacitance
Change
D.F.
I.R.
Dielectric
Strength
Appearance No marking defects
Capacitance
Change
D.F.
I.R.
Appearance No marking defects
Capacitance
Change
D.F.
I.R.
Appearance No marking defects
Capacitance
Change
D.F.
I.R.
Within 7.5%
W.V.: 25V min.; 0.025 max.
W.V.: 16V/10V max.; 0.035 max.
W.V.: 6.3V max.; 0.05 max.
More than 10,000M or 500 · F (whichever is smaller)
No failure
Within 12.5%
W.V.: 10V min.; 0.05 max.
W.V.: 6.3V max.; 0.075 max.
More than 1,000M or 50 · F (whichever is smaller)
Within 12.5%
W.V.: 10V min.; 0.05 max.
W.V.: 6.3V max.; 0.075 max.
More than 500M or 25 · F
(whichever is smaller)
Within 12.5%
W.V.: 10V min.; 0.05 max.
W.V.: 6.3V max.; 0.075 max.
More than 1,000M or 50 · F
(whichever is smaller)
When no "*" is added in PNs table, please refer to LLL/LLR/LLA/LLM Series Specifications and Test Methods (1).
When "*" is added in PNs table, please refer to LLL/LLR/LLA/LLM Series Specifications and Test Methods (2).
Specifications
Fix the capacitor to the supporting jig in the same manner and
under the same conditions as (10).
Perform the five cycles according to the four heat treatments
listed in the following table. Let sit for 24 2 hours at room
temperature, then measure.
• Initial measurement.
Set the capacitor at 40 2 C and 90 to 95% humidity for 500 12
hours. Remove and let sit for 24 2 hours at room temperature,
then measure.
Apply the rated voltage at 40 2 C and 90 to 95% humidity for
500 12 hours. Remove and let sit for 24 2 hours at room
temperature, then measure. The charge/discharge current is
less than 50mA.
Apply 200% of the rated voltage for 1000 12 hours at the
maximum operating temperature 3 C. Let sit for 24 2 hours
at room temperature, then measure. The charge/discharge
current is less than 50mA.
•Initial measurement.
Perform a heat treatment at 150+0/–10 C for one hour and
then let sit for 24 2 hours at room temperature. Perform the
initial measurement.
Apply 200% of the rated DC voltage for one hour at the
maximum operating temperature 3 C. Remove and let sit for
24 2 hours at room temperature.
Perform initial measurement.
Temp. ( C)
Time (min.)
Step
Min. Operating
Temp. +0/–3
30 3
1
Test Method
Temp.
Room
2 to 3
2
Max. Operating
Temp. +3/–0
30 3
3
Temp.
Room
2 to 3
4
C02E.pdf
10.12.20