ADF4216BRUZ-RL7 Analog Devices Inc, ADF4216BRUZ-RL7 Datasheet - Page 19

• Manufacturer Part Number: ADF4216BRUZ-RL7
• Description: DUAL PLL,1.2/0.5GHz I.C
• Manufacturer: Analog Devices Inc
• Type: Clock/Frequency Synthesizer (RF/IF)r

Specifications of ADF4216BRUZ-RL7

• Pll: Yes
• Input: CMOS
• Output: Clock
• Number Of Circuits: 1
• Ratio - Input:output: 3:1
• Differential - Input:output: Yes/No
• Frequency - Max: 1.2GHz
• Divider/multiplier: Yes/No
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP
• Frequency-max: 1.2GHz
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

INTERFACING
The ADF4216/ADF4217/ADF4218 family has a simple SPI-
compatible serial interface for writing to the device. SCLK,
SDATA, and LE (Latch Enable) control the data transfer. When
LE goes high, the 22 bits that have been clocked into the input
register on each rising edge of SCLK will be transferred to the
appropriate latch. See Figure 1 for the Timing Diagram and
Table I for the Latch Truth Table.
The maximum allowable serial clock rate is 20 MHz. This
means that the maximum update rate possible for the device is
909 kHz or one update every 1.1 ms. This is certainly more than
adequate for systems that will have typical lock times in hun-
dreds of microseconds.
ADuC812 Interface
Figure 9 shows the interface between the ADF421x family and
the ADuC812 microconverter. Since the ADuC812 is based on
an 8051 core, this interface can be used with any 8051-based
microcontroller. The microconverter is set up for SPI Master
Mode with CPHA = 0. To initiate the operation, the I/O port
driving LE is brought low. Each latch of the ADF421x family
needs a 22-bit word. This is accomplished by writing three 8-bit
bytes from the microconverter to the device. When the third
byte has been written, the LE input should be brought high to
complete the transfer.
On first applying power to the ADF421x family, it requires four
writes (one each to the R counter latch and the AB counter latch
for both RF1 and RF2 side) for the output to become active.
When operating in the mode described, the maximum SCLOCK
rate of the ADuC812 is 4 MHz. This means that the maximum
rate at which the output frequency can be changed will be about
180 kHz.
ADuC812
I/O PORTS
SCLOCK
MOSI
SCLK
SDATA
LE
MUXOUT
(LOCK DETECT)
ADF4216/
ADF4217/
ADF4218
ADSP-2181 Interface
Figure 10 shows the interface between the ADF421x family and
the ADSP-21xx Digital Signal Processor. As previously noted,
the ADF421x family needs a 22-bit serial word for each latch
write. The easiest way to accomplish this using the ADSP-21xx
family is to use the Autobuffered Transmit Mode of operation
with Alternate Framing. This provides a means for transmitting
an entire block of serial data before an interrupt is generated.
Set up the word length for eight bits and use three memory
locations for each 22-bit word. To program each 22-bit latch,
store the three 8-bit bytes, enable the Autobuffered mode and
then write to the transmit register of the DSP. This last opera-
tion initiates the autobuffer transfer.
ADSP-21xx
ADF4216/ADF4217/ADF4218
I/O FLAG
SCLK
TFS
DT
SCLK
SDATA
LE
MUXOUT
(LOCK DETECT)
ADF4216/
ADF4217/
ADF4218