ADSP-BF512KSWZ-3 Analog Devices Inc, ADSP-BF512KSWZ-3 Datasheet - Page 17

• Manufacturer Part Number: ADSP-BF512KSWZ-3
• Description: Low-Power Blackfin Processor
• Manufacturer: Analog Devices Inc
• Series: Blackfin®r
• Type: Fixed Pointr

Specifications of ADSP-BF512KSWZ-3

• Interface: I²C, PPI, SPI, SPORT, UART/USART
• Clock Rate: 300MHz
• Non-volatile Memory: External
• On-chip Ram: 116kB
• Voltage - I/o: 1.8V, 2.5V, 3.3V
• Voltage - Core: 1.30V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 176-LQFP Exposed Pad, 176-eLQFP, 176-HLQFP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

SIGNAL DESCRIPTIONS
The processors’ signal definitions are listed in
to maintain maximum function and reduce package size and
signal count, some signals have dual, multiplexed functions. In
cases where signal function is reconfigurable, the default state is
shown in plain text, while the alternate function is shown in
italics.
All pins are three-stated during and immediately after reset,
with the exception of the external memory interface, asynchro-
nous and synchronous memory control, and the buffered XTAL
output pin (CLKBUF). On the external memory interface, the
control and address lines are driven high, with the exception of
CLKOUT, which toggles at the system clock rate. During hiber-
nate all outputs are three-stated unless otherwise noted in
Table
All I/O signals have their input buffers disabled with the excep-
tion of the signals noted in the data sheet that need pull-ups or
pull downs if unused.
Table 7. Signal Descriptions
Signal Name
EBIU
ADDR19–1
DATA15–0
ABE1–0/SDQM1–0
AMS1–0
ARE
AWE
SRAS
SCAS
SWE
SCKE
CLKOUT
SA10
SMS
Port F: GPIO and Multiplexed Peripherals
PF0/ETxD2/PPI D0/SPI1SEL2/TACLK6
PF1/ERxD2/PPI D1/PWM AH/TACLK7
PF2/ETxD3/PPI D2/PWM AL
PF3/ERxD3/PPI D3/PWM BH/TACLK0
PF4/ERxCLK/PPI D4/PWM BL/TACLK1
PF5/ERxDV/PPI D5/PWM CH/TACI0
PF6/COL/PPI D6/PWM CL/TACI1
PF7/SPI0SEL1/PPI D7/PWMSYNC
7.
ADSP-BF512/BF512F, BF514/BF514F, BF516/BF516F, BF518/BF518F
Type Function
O
I/O
O
O
O
O
O
O
O
O
O
O
O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
I/O
Table
Rev. B | Page 17 of 68 | January 2011
Address Bus
Data Bus
Byte Enable or Data Mask
Asynchronous Memory Bank Selects (Require pull-ups if hibernate is used)
Asynchronous Memory Read Enable
Asynchronous Memory Write Enable
SDRAM Row Address Strobe
SDRAM Column Address Strobe
SDRAM Write Enable
SDRAM Clock Enable (Requires a pull-down if hibernate with SDRAM self-refresh
is used)
SDRAM Clock Output
SDRAM A10 Signal
SDRAM Bank Select
GPIO/Ethernet MII Transmit D2/PPI Data 0/SPI1 Slave Select 2/Timer6 Alternate
Clock
GPIO/Ethernet MII Receive D2/PPI Data 1/PWM AH Output/Timer7 Alternate Clock C
GPIO/Ethernet Transmit D3/PPI Data 2/PWM AL Output
GPIO/Ethernet MII Data Receive D3/PPI Data 3/PWM BH Output/Timer0 Alternate
Clock
GPIO/Ethernet MII Receive Clock/PPI Data 4/PWM BL Out/Timer1 Alternate CLK
GPIO/Ethernet MII Receive Data Valid/PPI Data 5/PWM CH Out
/Timer0 Alternate Capture Input
GPIO/Ethernet MII Collision/PPI Data 6/PWM CL Out/Timer1 Alternate Capture Input C
GPIO/SPI0 Slave Select 1/PPI Data 7/PWM Sync
7. In order
The SDA (serial data) and SCL (serial clock) pins/balls are open
drain and therefore require a pullup resistor. Consult version
2.1 of the I
It is strongly advised to use the available IBIS models to ensure
that a given board design meets overshoot/undershoot and sig-
nal integrity requirements. If no IBIS simulation is performed, it
is strongly recommended to add series resistor terminations for
all Driver Types A, C and D. The termination resistors should
be placed near the processor to reduce transients and improve
signal integrity. The resistance value, typically 33 Ω or 47 Ω,
should be chosen to match the average board trace impedance.
Additionally, adding a parallel termination to CLKOUT may
prove useful in further enhancing signal integrity. Be sure to
verify overshoot/undershoot and signal integrity specifications
on actual hardware.
2
C specification for the proper resistor value.
Driver
Type
A
A
A
A
A
A
A
A
A
A
B
A
A
C
C
C
C
C
C
1