SLXT334QE.B3 Intel, SLXT334QE.B3 Datasheet - Page 25

• Manufacturer Part Number: SLXT334QE.B3
• Manufacturer: Intel

Specifications of SLXT334QE.B3

• Operating Supply Voltage (typ): 5V
• Screening Level: Industrial
• Mounting: Surface Mount
• Operating Supply Voltage (min): 4.75V
• Operating Supply Voltage (max): 5.25V
• Operating Temperature (min): -40C
• Operating Temperature (max): 85C
• Lead Free Status / RoHS Status: Not Compliant

Datasheet
Transmit return loss
Transmit load capacitance
Permissible cable attenuation
Receiver dynamic range
Signal to noise interference margin
Signal to single tone interference margin
Data decision threshold
Analog loss of signal threshold
Loss of signal threshold hysteresis
Consecutive zeros before loss of signal
Low limit input jitter
tolerance
RCLK output jitter
Clock recovery PLL 3 dB bandwidth
PLL peaking
Receiver input impedance
1. Typical figures are at 25 °C and are for design aid only; not guaranteed and not subject to production testing.
2. With no jitter at the input used for synchronization or when using an externally supplied jitter free master clock the peak to
3. The signal level is the power level measured in a 3 kHz bandwidth at the point where the signal arrives at the distribution
4. Guaranteed by design and other correlation methods.
1. Typical figures are at 25 °C and are for design aid only; not guaranteed and not subject to production testing.
2. No errors shall occur when the combined signal attenuated by the maximum specified interconnecting cable loss is applied to
3. Sine wave jitter and wander with a peak to peak amplitude that corresponds at least to what is specified in
4. If the LXT334 is configured as data receiver only and if a jitter free signal is applied to RTIP and RRING the added jitter must
5. Equal to 22 dB below the nominal 0 dB level in 120
6. Guaranteed by design and other correlation methods.
peak
frame for
the input port. See ITU O.151 recommendation for further details.
cause either a bit error or loss of frame alignment. As test signal an HDB3-coded digital signal with an electrical characteristic
that complies with what is set forth in ITU G.703 shall be used. Test sequence is pseudo-random 2
not exceed the specified value.
Table 9. 1.544 MHz Transmit Characteristics (over recommended range) (Continued)
Table 10. 2.048 MHz Receive Characteristics (over recommended range)
jitter will not exceed the specified value.
an all 1s pattern transmitted.
3
6
4, 6
4
Parameter
Parameter
51 kHz to 102 kHz
102 kHz to 2.048 MHz
2.048 MHz to 3.072 MHz
2
1.2E-5 Hz to 20 Hz
20 Hz to 2.4 kHz
8 kHz to 100 kHz
0 Hz to100 kHz
2, 6
Quad Short-Haul Transceiver with Clock Recovery — LXT334
4
6
systems.
Sym
SRE
Sym
S/X
C
DR
S/I
–
–
–
–
–
–
–
–
–
–
–
–
–
–
RT
Min
-15
-14
0.5
1.5
0.2
43
36
Min
–
–
–
–
–
–
–
–
18
18
18
–
Typ
225
0.01
2.5
50
32
10
40
Typ
–
–
–
–
–
–
–
–
180
–
–
–
1
5
1
Max
4.2
12
57
–
–
–
–
–
–
–
–
–
–
0
–
Max
–
–
–
–
Unit
kHz
mV
U.I.
U.I.
U.I.
U.I.
dB
Vp
dB
dB
dB
dB
k
%
Unit
dB
dB
dB
pF
15
@1024 kHz
Per G.703, O.151, 6 dB of
cable.
O.151, 6 dB of cable
Relative to peak input
voltage.
G.775 recommendation
G.735 recommendation
peak to peak
@1024 kHz RTIP to
RRING
See Note 1.
-1. See also ITU O.151.
See Applications
Information section
Figure
Test Condition
Test Condition
Figure 18
11.
shall not
25