PIC18F65K90T-I/MR Microchip Technology, PIC18F65K90T-I/MR Datasheet - Page 160

• Manufacturer Part Number: PIC18F65K90T-I/MR
• Description: 32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 QFN 9x9x0.9mm T/R
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F65K90T-I/MR

• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 32 KB
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 8
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 53
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-VFQFN Exposed Pad
• Lead Free Status / Rohs Status: Details

corresponding Data Direction and Output Latch registers
PIC18F87K90 FAMILY
11.3
PORTB is an 8-bit wide, bidirectional port. The
are TRISB and LATB. All pins on PORTB are digital only.
EXAMPLE 11-2:
Each of the PORTB pins has a weak internal pull-up. A
single control bit can turn on all the pull-ups. This is
performed by clearing bit, RBPU (INTCON2<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are
disabled on a Power-on Reset.
DS39957D-page 160
CLRF
CLRF
MOVLW
MOVWF
PORTB, TRISB and
LATB Registers
PORTB
LATB
0CFh
TRISB
; Initialize PORTB by
; clearing output
; data latches
; Alternate method
; to clear output
; data latches
; Value used to
; initialize data
; direction
; Set RB<3:0> as inputs
; RB<5:4> as outputs
; RB<7:6> as inputs
INITIALIZING PORTB
Four of the PORTB pins (RB<7:4>) have an
interrupt-on-change feature. Only pins configured as
inputs can cause this interrupt to occur. Any RB<7:4>
pin configured as an output will be excluded from the
interrupt-on-change comparison.
Comparisons with the input pins (of RB<7:4>) are
made with the old value latched on the last read of
PORTB. The “mismatch” outputs of RB<7:4> are ORed
together to generate the RB Port Change Interrupt with
Flag bit, RBIF (INTCON<0>).
This
power-managed modes. To clear the interrupt in the
Interrupt Service Routine (ISR):
a)
b)
c)
A mismatch condition will continue to set flag bit, RBIF.
Reading PORTB will end the mismatch condition and
allow flag bit, RBIF, to be cleared after one T
The interrupt-on-change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt-on-change
feature. Polling of PORTB is not recommended while
using the interrupt-on-change feature.
The RB<3:2> pins are multiplexed as CTMU edge
inputs. RB5 has an additional function for Timer3 and
Timer1. It can be configured for the Timer3 clock input
or Timer1 external clock gate input.
The RB<5:0> pins also are multiplexed with LCD seg-
ment drives that are controlled by bits in the registers,
LCDSE1 and LCDSE3. I/O port functionality is only
available when the LCD segments are disabled.
Any read or write of PORTB (except with the
MOVFF (ANY), PORTB instruction). This will end
the mismatch condition.
Wait one instruction cycle (such as executing a
NOP instruction).
Clear flag bit, RBIF.
interrupt
 2009-2011 Microchip Technology Inc.
can
wake
the
device
CY
delay.
from