PIC18F65K90T-I/PT Microchip Technology, PIC18F65K90T-I/PT Datasheet - Page 443

• Manufacturer Part Number: PIC18F65K90T-I/PT
• Description: 32kB Flash, 2kB RAM, 1kB EE, NanoWatt XLP, LCD 64 TQFP 10x10x1mm T/R
• Manufacturer: Microchip Technology
• Series: PIC® XLP™ 18Fr

Specifications of PIC18F65K90T-I/PT

• Processor Series: PIC18F
• Core: PIC
• Data Bus Width: 8 bit
• Program Memory Type: Flash
• Program Memory Size: 32 KB
• Data Ram Size: 2 KB
• Interface Type: I2C, SPI
• Maximum Clock Frequency: 64 MHz
• Number Of Timers: 8
• Operating Supply Voltage: 1.8 V to 5.5 V
• Maximum Operating Temperature: + 125 C
• 3rd Party Development Tools: 52715-96, 52716-328, 52717-734, 52712-325, EWPIC18
• Minimum Operating Temperature: - 40 C
• On-chip Adc: 12 bit, 16 Channel
• Core Processor: PIC
• Core Size: 8-Bit
• Speed: 64MHz
• Connectivity: I²C, LIN, SPI, UART/USART
• Peripherals: Brown-out Detect/Reset, LCD, POR, PWM, WDT
• Number Of I /o: 53
• Eeprom Size: 1K x 8
• Ram Size: 2K x 8
• Voltage - Supply (vcc/vdd): 1.8 V ~ 5.5 V
• Data Converters: A/D 16x12b
• Oscillator Type: Internal
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 64-TQFP
• Lead Free Status / Rohs Status: Details

28.3.2
The difference in the two regulators’ operation arises
with Sleep mode. The ultra low-power regulator gives
the device the lowest current in the Regulator Enabled
mode.
The on-chip regulator can go into a lower power mode,
when the device goes to Sleep, by setting the REGSLP
bit (WDTCON<7>). This puts the regulator in a standby
mode so that the device consumes much less current.
The on-chip regulator can also go into the Ultra Low-
Power mode, which consumes the lowest current
possible with the regulator enabled. This mode is
controlled by the RETEN bit (CONFIG1L<0>) and
SRETEN bit (WDTCON<4>).
TABLE 28-3:
 2009-2011 Microchip Technology Inc.
Enabled
Enabled
Enabled
Enabled
Enabled
Note 1:
Regulator
x = Indicates that V
OPERATION OF REGULATOR IN
SLEEP
SLEEP MODE REGULATOR SETTINGS
Normal Operation (Sleep)
Low-Power mode (Sleep)
Normal Operation (Sleep)
Low-Power mode (Sleep)
Ultra Low-Power mode (Sleep)
IT
Power Mode
status is invalid.
PIC18F87K90 FAMILY
WDTCON<7>
VREGSLP
The various modes of regulator operation are shown in
Table
When the ultra low-power regulator is in Sleep mode,
the internal reference voltages in the chip will be shut
off and any interrupts referring to the internal reference
will not wake up the device. If the BOR or LVD is
enabled, the regulator will keep the internal references
on and the lowest possible current will not be achieved.
When using the ultra low-power regulator in Sleep
mode, the device will take about 250  s, typical, to start
executing the code after it wakes up.
(1)
0
1
0
1
x
28-3.
WDTCON<4>
SRETEN
x
x
0
0
1
DS39957D-page 443
CONFIG1L<0>
RETEN
1
1
x
x
0