ISP1507ABS,118 NXP Semiconductors, ISP1507ABS,118 Datasheet - Page 59

• Manufacturer Part Number: ISP1507ABS,118
• Description: RF Transceiver USB 2.0 ULPI TRNSCVR
• Manufacturer: NXP Semiconductors

Specifications of ISP1507ABS,118

• Number Of Transceivers: 1
• Esd Protection: YeskV
• Power Supply Requirement: Single
• Operating Supply Voltage (typ): 3.3V
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Pin Count: 32
• Mounting: Surface Mount
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Lead Free Status / RoHS Status: Compliant
• Other names: 935285494118 ISP1507ABS-T

NXP Semiconductors
14. Static characteristics
Table 46.
V
Typical values are at V
[1]
Table 47.
Digital pins: CLOCK, DIR, STP, NXT, DATA[7:0], RESET_N and CHIP_SELECT_N; unless otherwise specified.
V
Typical values are at V
ISP1507A_ISP1507B_1
Product data sheet
Symbol
V
V
V
I
I
Symbol
Input levels
V
V
I
I
I
Output levels
V
CC
CC(I/O)
IL
IH
LI
CC
CC
(REG3V3)
(REG1V8)
POR(trip)
IL
IH
OL
= 3.0 V to 3.6 V; V
A continuous stream of 1 kB packets with minimum inter-packet gap and all data bits set to logic 0 for continuous toggling.
= 3.0 V to 3.6 V; V
Parameter
voltage on pin REG3V3
voltage on pin REG1V8
power-on reset trip voltage
supply current
supply current on
pin V
Parameter
LOW-level input voltage
HIGH-level input voltage
LOW-level input current
HIGH-level input current
input leakage current
LOW-level output voltage
Static characteristics: supply pins
Static characteristics: digital pins
CC(I/O)
CC
CC
CC(I/O)
CC(I/O)
= 3.3 V; V
= 3.3 V; V
= 1.65 V to 3.6 V; T
= 1.65 V to 3.6 V; T
CC(I/O)
CC(I/O)
Conditions
V
V
I
OL
Conditions
charge pump disabled
charge pump enabled
ULPI interface pins are static
I
I
= 3.3 V; T
= 3.3 V; T
= 0 V
= V
low-power mode; V
disabled; 1.5 k pull-up resistor on
pin DP disconnected
low-power mode; V
disabled; 1.5 k pull-up resistor on
pin DP connected
full-speed idle; no USB activity
high-speed idle; no USB activity
full-speed continuous data transmit;
50 pF load on pins DP and DM
full-speed continuous data receive
high-speed continuous data transmit;
45
high-speed continuous data receive
I
current only
I
current only
= +2 mA
O(VBUS)
O(VBUS)
CC(I/O)
load on pins DP and DM to ground
amb
amb
= 8 mA; charge pump supply
= 0 mA; charge pump supply
Rev. 01 — 19 May 2008
amb
amb
= 40 C to +85 C; unless otherwise specified.
= 40 C to +85 C; unless otherwise specified.
= +25 C; unless otherwise specified.
= +25 C; unless otherwise specified.
BUS
BUS
valid detector
valid detector
Min
-
0.7
-
-
-
1
ISP1507A; ISP1507B
V
CC(I/O)
[1]
[1]
[1]
[1]
Typ
-
-
-
-
+0.1
-
ULPI HS USB OTG transceiver
Min
3.0
1.65
1.0
-
-
-
-
-
-
-
-
-
-
-
Typ
3.3
1.8
-
35
215
10
19
15
11
48
28
20
300
-
Max
0.3
-
1
1
+1
0.4
© NXP B.V. 2008. All rights reserved.
V
Max
3.6
1.95
1.5
85
280
-
-
-
-
-
-
23
-
1
CC(I/O)
Unit
V
V
V
Unit
V
V
V
mA
mA
mA
mA
mA
mA
mA
58 of 81
A
A
A
A
A
A
A