ISP1507CBS,518 NXP Semiconductors, ISP1507CBS,518 Datasheet - Page 7

• Manufacturer Part Number: ISP1507CBS,518
• Description: RF Transceiver USB 2.0 ULPI TRNSCVR
• Manufacturer: NXP Semiconductors

Specifications of ISP1507CBS,518

• Number Of Transceivers: 1
• Esd Protection: YeskV
• Power Supply Requirement: Single
• Operating Supply Voltage (typ): 3.3V
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Dual Supply Voltage (typ): Not RequiredV
• Dual Supply Voltage (max): Not RequiredV
• Dual Supply Voltage (min): Not RequiredV
• Mounting: Surface Mount
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Lead Free Status / RoHS Status: Compliant
• Other names: 935285496518 ISP1507CBS-T

NXP Semiconductors
Table 2.
[1]
[2]
[3]
[4]
ISP1507C_ISP1507D_1
Product data sheet
Symbol
RESET_N/PSW_N 12
REG1V8
DIR
STP
NXT
DATA7
DATA6
DATA5
DATA4
CLOCK
DATA3
V
DATA2
GND
CC(I/O)
Symbol names ending with underscore N, for example, NAME_N, indicate active LOW signals.
For details on external components required on each pin, see bill of materials and application diagrams in
I = input; O = output; I/O = digital input/output; AI = analog input; AO = analog output; AI/O = analog input/output; P = power or ground
pin.
A detailed description of these pins can be found in
[1][2]
Pin description
Pin
13
14
15
16
17
18
19
20
21
22
23
24
die
pad
…continued
Type
I/O
P
O
I
O
I/O
I/O
I/O
I/O
O
I/O
P
I/O
P
[3]
Description
This pin has two possible functions:
RESET_N (input) — Active LOW, asynchronous reset input.
3.3 V tolerant; plain input
PSW_N (output) — Active LOW external V
pump enable.
open-drain; 3.3 V tolerant
If not used, this pin must be connected to V
1.8 V regulator output
ULPI direction signal
slew-rate controlled output (1 ns)
ULPI stop signal
plain input; programmable pull up
ULPI next signal
slew-rate controlled output (1 ns)
pin 7 of the bidirectional ULPI data bus
slew-rate controlled output (1 ns); plain input; programmable pull down
pin 6 of the bidirectional ULPI data bus
slew-rate controlled output (1 ns); plain input; programmable pull down
pin 5 of the bidirectional ULPI data bus
slew-rate controlled output (1 ns); plain input; programmable pull down
pin 4 of the bidirectional ULPI data bus
slew-rate controlled output (1 ns); plain input; programmable pull down
60 MHz clock output
slew-rate controlled output (1 ns)
pin 3 of the bidirectional ULPI data bus
slew-rate controlled output (1 ns); plain input; programmable pull down
I/O supply rail
pin 2 of the bidirectional ULPI data bus
slew-rate controlled output (1 ns); plain input; programmable pull down
ground supply; down bonded to the exposed die pad (heat sink); to be connected to
the PCB ground
Section
Rev. 01 — 28 May 2008
[4]
7.10.
ULPI HS USB host and peripheral transceiver
ISP1507C; ISP1507D
BUS
CC(I/O)
power switch or external charge
.
Section
© NXP B.V. 2008. All rights reserved.
16.
6 of 74