MT9HTF6472PY-667F1 Micron Technology Inc, MT9HTF6472PY-667F1 Datasheet

no-image

MT9HTF6472PY-667F1

Manufacturer Part Number
MT9HTF6472PY-667F1
Description
Manufacturer
Micron Technology Inc
Datasheet

Specifications of MT9HTF6472PY-667F1

Main Category
DRAM Module
Sub-category
DDR2 SDRAM
Module Type
240RDIMM
Device Core Size
72b
Organization
64Mx72
Total Density
512MByte
Chip Density
512Mb
Maximum Clock Rate
667MHz
Operating Supply Voltage (typ)
1.8V
Operating Current
1.62A
Number Of Elements
9
Operating Supply Voltage (max)
1.9V
Operating Supply Voltage (min)
1.7V
Operating Temp Range
0C to 70C
Operating Temperature Classification
Commercial
Pin Count
240
Mounting
Socket
Lead Free Status / RoHS Status
Compliant
DDR2 SDRAM RDIMM
MT9HTF3272Y – 256MB
MT9HTF6472PY – 512MB
MT9HTF12872PY – 1GB
Features
• 240-pin, registered dual in-line memory module
• Fast data transfer rates: PC2-3200, PC2-4200,
• 256MB (32 Meg x 72), 512MB (64 Meg x 72), or
• Supports ECC error detection and correction
• V
• V
• JEDEC-standard 1.8V I/O (SSTL_18-compatible)
• Differential data strobe (DQS, DQS#) option
• 4n-bit prefetch architecture
• Multiple internal device banks for concurrent
• Programmable CAS# latency (CL)
• Posted CAS# additive latency (AL)
• WRITE latency = READ latency - 1
• Programmable burst lengths (BL): 4 or 8
• Adjustable data-output drive strength
• 64ms, 8192-cycle refresh
• On-die termination (ODT)
• Serial presence-detect (SPD) with EEPROM
• Single rank
• Gold edge contacts
Table 1: Key Timing Parameters
PDF: 09005aef82250868
htf9c32_64_128x72.pdf - Rev. F 3/10 EN
PC2-5300, or PC2-6400
1GB (128 Meg x 72)
operation
Speed
Grade
DD
DDSPD
-80E
-800
-667
-53E
-40E
= V
DDQ
= 1.7–3.6V
= 1.8V
Products and specifications discussed herein are subject to change by Micron without notice.
Nomenclature
Industry
PC2-6400
PC2-6400
PC2-5300
PC2-4200
PC2-3200
256MB, 512MB, 1GB (x72, ECC, SR) 240-Pin DDR2 SDRAM RDIMM
t
CK
CL = 6
800
800
CL = 5
Data Rate (MT/s)
800
667
667
1
Figure 1: 240-Pin RDIMM (MO-237
R/C A, Nonparity; R/C F, Parity)
CL = 4
Module height: 30mm (1.18in)
Options
• Parity
• Operating temperature
• Package
• Frequency/CL
533
533
553
553
400
Notes:
– Commercial (0°C ≤ T
– Industrial (–40°C ≤ T
– 240-pin DIMM (lead-free)
– 2.5ns @ CL = 5 (DDR2-800)
– 2.5ns @ CL = 6 (DDR2-800)
– 3.0ns @ CL = 5 (DDR2-667)
– 3.75ns @ CL = 4 (DDR2-533)
– 5.0ns @ CL = 3 (DDR2-400)
Micron Technology, Inc. reserves the right to change products or specifications without notice.
1. Contact Micron for industrial temperature
2. CL = CAS (READ) latency; registered mode
3. Not available in 256MB module density.
CL = 3
400
400
400
400
400
module offerings.
will add one clock cycle to CL.
2
t
(ns)
12.5
RCD
15
15
15
15
A
A
≤ +85°C)
≤ +70°C)
© 2003 Micron Technology, Inc. All rights reserved.
3
3
1
(ns)
12.5
t
15
15
15
15
RP
Marking
Features
None
-80E
-800
-667
-53E
-40E
P
Y
I
(ns)
t
55
55
55
55
55
RC

Related parts for MT9HTF6472PY-667F1

MT9HTF6472PY-667F1 Summary of contents

Page 1

... ECC, SR) 240-Pin DDR2 SDRAM RDIMM DDR2 SDRAM RDIMM MT9HTF3272Y – 256MB MT9HTF6472PY – 512MB MT9HTF12872PY – 1GB Features • 240-pin, registered dual in-line memory module • Fast data transfer rates: PC2-3200, PC2-4200, PC2-5300, or PC2-6400 • 256MB (32 Meg x 72), 512MB (64 Meg x 72), or 1GB (128 Meg x 72) • ...

Page 2

... ECC, SR) 240-Pin DDR2 SDRAM RDIMM Table 2: Addressing Parameter Refresh count Row address Device bank address Device configuration 256Mb (32 Meg x 8) Column address Module rank address Table 3: Part Numbers and Timing Parameters – 256MB 1 Base device: MT47H32M8, 256Mb DDR2 SDRAM Module 2 Part Number Density ...

Page 3

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Pin Assignments Table 6: Pin Assignments 240-Pin RDIMM Front Pin Symbol Pin Symbol Pin Symbol Pin Symbol Pin Symbol Pin Symbol Pin Symbol Pin Symbol DQ19 61 ...

Page 4

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Table 6: Pin Assignments (Continued) 240-Pin RDIMM Front Pin Symbol Pin Symbol Pin Symbol Pin Symbol Pin Symbol Pin Symbol Pin Symbol Pin Symbol ...

Page 5

... ECC, SR) 240-Pin DDR2 SDRAM RDIMM Pin Descriptions The pin description table below is a comprehensive list of all possible pins for all DDR2 modules. All pins listed may not be supported on this module. See Pin Assignments for information specific to this module. Table 7: Pin Descriptions ...

Page 6

... SPD EEPROM power supply: 1.7–3.6V. Reference voltage: V /2. DD Ground. No connect: These pins are not connected on the module. No function: These pins are connected within the module, but provide no functionality. Not used: These pins are not used in specific module configurations/operations. Reserved for future use. 6 Pin Descriptions and V ...

Page 7

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Functional Block Diagram Figure 2: Functional Block Diagram – Raw Card A, Nonparity RS0# DQS0 DQS0# DM0/DQS9 NC/DQS9# DM/ NU/ CS# DQS DQS# RDQS RDQS# DQ0 DQ DQ1 DQ DQ2 ...

Page 8

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Figure 3: Functional Block Diagram – Raw Card F, Parity RS0# DQS0 DQS0# DM0/DQS9 NC/DQS9# DM/ NU/ CS# DQS DQS# RDQS RDQS# DQ0 DQ DQ1 DQ DQ2 DQ DQ3 DQ ...

Page 9

... DRAM core and eight corresponding n-bit-wide, one-half-clock-cycle data trans- fers at the I/O pins. DDR2 modules use two sets of differential signals: DQS, DQS# to capture data and CK and CK# to capture commands, addresses, and control signals. Differential clocks and data strobes ensure exceptional noise immunity for these signals and provide precise crossing points to capture input signals ...

Page 10

... ECC, SR) 240-Pin DDR2 SDRAM RDIMM Electrical Specifications Stresses greater than those listed may cause permanent damage to the module. This is a stress rating only, and functional operation of the module at these or any other condi- tions outside those indicated in each device's data sheet is not implied. Exposure to absolute maximum rating conditions for extended periods may adversely affect reliability ...

Page 11

... Component specifications are available on Micron's Web site. Module speed grades cor- relate with component speed grades. Table 9: Module and Component Speed Grades DDR2 components may exceed the listed module speed grades; module may not be available in all listed speed grades Module Speed Grade -1GA ...

Page 12

ECC, SR) 240-Pin DDR2 SDRAM RDIMM I Specifications DD Table 10: DDR2 I Specifications and Conditions – 256MB DD Values shown for MT47H32M8 DDR2 SDRAM only and are computed from values specified in the 256Mb (32 ...

Page 13

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Table 10: DDR2 I Specifications and Conditions – 256MB (Continued) DD Values shown for MT47H32M8 DDR2 SDRAM only and are computed from values specified in the 256Mb (32 Meg x ...

Page 14

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Table 11: DDR2 I Specifications and Conditions – 512MB DD Values shown for MT47H64M8 DDR2 SDRAM only and are computed from values specified in the 512Mb (64 Meg x 8) ...

Page 15

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Table 11: DDR2 I Specifications and Conditions – 512MB (Continued) DD Values shown for MT47H64M8 DDR2 SDRAM only and are computed from values specified in the 512Mb (64 Meg x ...

Page 16

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Table 12: DDR2 I Specifications and Conditions (Die Revision A) – 1GB DD Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the 1Gb (128 ...

Page 17

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Table 12: DDR2 I Specifications and Conditions (Die Revision A) – 1GB (Continued) DD Values shown for MT47H128M8 DDR2 SDRAM only and are computed from values specified in the 1Gb ...

Page 18

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Table 13: DDR2 I Specifications and Conditions (Die Revision E) – 1GB DD Values shown for MT47H256M4 DDR2 SDRAM only and are computed from values specified in the 1Gb (256 ...

Page 19

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Table 13: DDR2 I Specifications and Conditions (Die Revision E) – 1GB (Continued) DD Values shown for MT47H256M4 DDR2 SDRAM only and are computed from values specified in the 1Gb ...

Page 20

... I REF RESET 1.8V DD RESET tion of the DDR2 SDRAM RDIMMs. These are meant subset of the parameters for the specific device used on the module. Detailed information for this register is available in JEDEC standard JESD82. 20 Register and PLL Specifications Min V + 125 V REF(DC) DDQ 0 V REF(DC) ...

Page 21

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Table 15: PLL Specifications CU877 device or equivalent Parameter Symbol DC high-level V IH input voltage DC low-level V IL input voltage Input voltage (limits high-level V ...

Page 22

ECC, SR) 240-Pin DDR2 SDRAM RDIMM Serial Presence-Detect For the latest SPD data, refer to Micron's SPD page: www.micron.com/SPD. Table 17: SPD EEPROM Operating Conditions Parameter/Condition Supply voltage Input high voltage: logic 1; All inputs Input ...

Page 23

... 0.76 (0.030) R 1.0 (0.039) 0.80 (0.031) TYP TYP 70.67 (2.78) TYP 123.0 (4.840) TYP Back view No components this side of module 5.0 (0.197) TYP 55.0 (2.165) 63.0 (2.48) TYP TYP complete design dimensions. times occur. 23 Module Dimensions U10 U11 U12 30.15 (1.185) 29 ...

Related keywords