82V3355DKG IDT, Integrated Device Technology Inc, 82V3355DKG Datasheet - Page 55

• Manufacturer Part Number: 82V3355DKG
• Manufacturer: IDT, Integrated Device Technology Inc

Specifications of 82V3355DKG

• Function: Wan PLL
• Operating Temperature (max): 85C
• Operating Temperature (min): -40C
• Package Type: TQFP
• Pin Count: 64
• Mounting: Surface Mount
• Lead Free Status / RoHS Status: Compliant

INPUT_MODE_CNFG - Input Mode Configuration
Programming Information
IDT82V3355
Address: 09H
Type: Read / Write
Default Value: 10100X10
AUTO_EXT_SY
4 - 3
Bit
7
6
5
2
1
0
NC_EN
7
AUTO_EXT_SYNC_EN
PH_ALARM_TIMEOUT
REVERTIVE_MODE
SYNC_FREQ[1:0]
IN_SONET_SDH
EXT_SYNC_EN
EXT_SYNC_EN
Name
-
6
This bit is valid only when the SYNC_BYPASS bit (b7, 7CH) is ‘0’.
Refer to the description of the EXT_SYNC_EN bit (b6, 09H).
This bit is valid only when the SYNC_BYPASS bit (b7, 7CH) is ‘0’.
This bit, together with the AUTO_EXT_SYNC_EN bit (b7, 09H), determines whether the selected frame sync input signal is
enabled to synchronize the frame sync output signals.
This bit determines how to clear the phase lock alarm.
0: The phase lock alarm will be cleared when a ‘1’ is written to the corresponding INn_CMOS_PH_LOCK_ALARM (n = 1, 2
or 3) / INn_DIFF_PH_LOCK_ALARM (n = 1 or 2) bit (b4/0, 44H/45H/47H).
1: The phase lock alarm will be cleared after a period (= TIME_OUT_VALUE[5:0] (b5~0, 08H) X MULTI_FACTOR[1:0]
(b7~6, 08H) in second) which starts from when the alarm is raised. (default)
These bits set the frequency of the frame sync signals input on the EX_SYNC1 ~ EX_SYNC3 pins.
00: 8 kHz (default)
01: 8 kHz.
10: 4 kHz.
11: 2 kHz.
This bit selects the SDH or SONET network type.
0: SDH. The DPLL required clock is 2.048 MHz when the IN_FREQ[3:0] bits (b3~0, 16H, 17H, 19H, 1AH & 1DH) are ‘0001’
and the T0/T4 DPLL output from the 16E1/16T1 path is 16E1.
1: SONET. The DPLL required clock is 1.544 MHz when the IN_FREQ[3:0] bits (b3~0, 16H, 17H, 19H, 1AH & 1DH) are
‘0001’ and the T0/T4 DPLL output from the 16E1/16T1 path is 16T1.
The default value of this bit is determined by the SONET/SDH pin during reset.
Reserved.
This bit selects Revertive or Non-Revertive switch for T0 path.
0: Non-Revertive switch. (default)
1: Revertive switch.
AUTO_EXT_SYNC_EN
PH_ALARM_TI
MEOUT
don’t-care
5
0
1
SYNC_FREQ1
EXT_SYNC_EN
4
0
1
1
55
SYNC_FREQ0
3
Description
IN_SONET_SD
H
2
SYNCHRONOUS ETHERNET WAN PLL
Synchronization
Disabled (default)
Disabled
Enabled
1
-
REVERTIVE_M
March 3, 2009
ODE
0