ICM7217AIPI Intersil, ICM7217AIPI Datasheet - Page 14

• Manufacturer Part Number: ICM7217AIPI
• Description: 4 DIGIT UP/DOWN COUNTER 0-9999
• Manufacturer: Intersil
• Type: 4-Digit UP/Down Counterr

Specifications of ICM7217AIPI

• Rohs Status: RoHS non-compliant
• Count: 9999
• Frequency: 2MHz
• Voltage - Supply: 4.5 V ~ 5.5 V
• Current - Supply: 100mA
• Operating Temperature: -25°C ~ 85°C
• Package / Case: 28-DIP (0.600", 15.24mm)
• Other names: ICM7217AIPIIS

It is possible to use separate thumbwheel switches for
presetting, but since the devices load data with the oscillator
free-running, the multiplexing of the two devices is difficult to
synchronize.
Precision Frequency Counter/Tachometer
The circuit shown in Figure 23 is a simple implementation of
a four digit frequency counter, using an ICM7207A to pro-
vide the one second gating window and the STORE and
RESET signals. In this configuration, the display reads hertz
directly. With Pin 11 of the ICM7027A connected to V
gating time will be 0.1s; this will display tens of hertz at the
least significant digit. For shorter gating times, an ICM7207
may be used (with a 6.5536MHz crystal), giving a 0.01s gat-
ing with Pin 11 connected to V
11 open.
To implement a four digit tachometer, the ICM7207A with
one second gating should be used. To get the display to
read directly in RPM, the rotational frequency of the object to
STORE
UP/DOWN
RESET
LOAD COUNTER/
I/O OFF
LOAD REGlSTER/
OFF
DISPLAY CONTrol
INPUT
DD
20 Common Cathode
, and a 0.1s gating with Pin
23 Common Anode
TERMINAL
TABLE 2. CONTROL INPUT DEFINITIONS ICM7217
10
14
12
11
9
DD
ICM7217
V
V
V
Unconnected
V
V
Unconnected
V
V
Unconnected
, the
V
V
V
V
V
DD
DD
DD
DD
SS
DD
SS
SS
SS
SS
DD
SS
(or floating)
(or floating)
(or floating)
14
be measured must be multiplied by 60. This can be done
electronically using a phase-locked loop, or mechanically by
using a disc rotating with the object with the appropriate
number of holes drilled around its edge to interrupt the light
from an LED to a photo-dector. For faster updating, use 0.1s
gating, and multiply the rotational frequency by 600.
Auto-Tare System
This circuit uses the count-up and count-down functions of
the ICM7217, controlled via the EQUAL and ZERO outputs,
to count in SYNC with an ICL7109A and ICL7109D Con-
verter as shown in Figure 24. By RESETing the ICM7217 on
a “tare” value conversion, and STORE-ing the result of a true
value conversion, an automatic fare subtraction occurs in the
result.
The ICM7217 stays in step with the ICL7109 by counting up
and down between 0 and 4095, for 8192 total counts, the
same number as the ICL7109 cycle. See applications note
No. A047 for more details.
VOLTAGE
Output Latches Not Updated
Output Latches Updated
Counter Counts Up
Counter Counts Down
Normal Operation
Counter Reset
Normal Operation
Counter Loaded with BCD data
BCD Port Forced to Hi-Z Condition
Normal Operation
Register Loaded with BCD Data
Display Drivers Disabled; BCD Port
Forced to Hi-Z Condition, mpx Counter
Reset to D4; mpx Oscillator Inhibited
Normal Operation
Segment Drivers Disabled
Leading Zero Blanking Inhibited
FUNCTION