ISL12024IBZ-T Intersil, ISL12024IBZ-T Datasheet - Page 11

• Manufacturer Part Number: ISL12024IBZ-T
• Description: IC RTC/CALENDAR EEPROM 8-SOIC
• Manufacturer: Intersil
• Type: Clock/Calendar/EEPROMr

Specifications of ISL12024IBZ-T

• Memory Size: 4K (512 x 8)
• Time Format: HH:MM:SS (12/24 hr)
• Date Format: YY-MM-DD-dd
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.7 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Rohs Compliant: YES
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: ISL12024IBZ-TTR

Alarm Registers (Non-Volatile)
Alarm0 and Alarm1
The alarm register bytes are set up identical to the RTC
register bytes, except that the MSB of each byte functions as
an enable bit (enable = “1”). These enable bits specify which
alarm registers (seconds, minutes, etc.) are used to make
the comparison. Note that there is no alarm byte for year.
The alarm function works as a comparison between the
alarm registers and the RTC registers. As the RTC
advances, the alarm will be triggered once a match occurs
between the alarm registers and the RTC registers. Any one
alarm register, multiple registers, or all registers can be
enabled for a match. See “Device Operation” on page 12
and “Application Section” on page 20 for more information.
Control Registers (Non-Volatile)
The Control Bits and Registers described under this section
are non-volatile.
BL Register
BP2, BP1, BP0 - Block Protect Bits
The Block Protect Bits, BP2, BP1 and BP0, determine which
blocks of the array are write protected. A write to a protected
block of memory is ignored. The block protect bits will
prevent write operations to one of eight segments of the
array. The partitions are described in Table 3.
INT Register: Interrupt Control and
Frequency Output Register
IM, AL1E, AL0E - Interrupt Control and Status Bits
There are two Interrupt Control bits, Alarm 1 Interrupt Enable
(AL1E) and Alarm 0 Interrupt Enable (AL0E) to specifically
enable or disable the alarm interrupt signal output
(IRQ/F
AL1E or AL0E or both bits are set to ‘1’ and both the FO1
and FO0 bits are set to 0 (F
0
0
0
0
1
1
1
1
OUT
0
0
1
1
0
0
1
1
). The interrupts are enabled when either the
0
1
0
1
0
1
0
1
PROTECTED ADDRESSES
None (Default)
180
100
000
000
000
000
000
TABLE 3.
ISL12024
OUT
h
h
h
h
h
h
h
11
– 1FF
– 1FF
– 1FF
– 03F
– 07F
– 0FF
– 1FF
disabled).
h
h
h
h
h
h
h
ARRAY LOCK
First 16 Pages
First 4 Pages
First 8 Pages
Upper 1/4
Upper 1/2
Full Array
Full Array
None
ISL12024
The IM bit enables the pulsed interrupt mode. To enter this
mode, the AL0E or AL1E bits are set to “1”, and the IM bit to
“1”. The IRQ/F
alarm occurs. This means that once the interrupt mode
alarm is set, it will continue to alarm for each occurring
match of the alarm and present time. This mode is
convenient for hourly or daily hardware interrupts in
microcontroller applications such as security cameras or
utility meter reading.
In this case both Alarms are enabled.
FO1, FO0 - Programmable Frequency Output Bits
These are two output control bits. They select one of three
divisions of the internal oscillator, that is applied to the
IRQ/F
this output. When using this function, the Alarm output
function is disabled.
Oscillator Compensation Registers
There are two trimming options.
• ATR. Analog Trimming Register
• DTR. Digital Trimming Register
These registers are non-volatile. The combination of analog
and digital trimming can give up to -64ppm to +110 ppm of
total adjustment.
ATR Register - ATR5, ATR4, ATR3, ATR2, ATR1,
ATR0: Analog Trimming Register
Six analog trimming bits, ATR0 to ATR5, are provided in
order to adjust the on-chip load capacitance value for
frequency compensation of the RTC. Each bit has a different
weight for capacitance adjustment. For example, using a
Citizen CFS-206 crystal with different ATR bit combinations
provides an estimated ppm adjustment range from -34ppm
to +80ppm to the nominal frequency compensation.
FO1
TABLE 4. PROGRAMMABLE FREQUENCY OUTPUT BITS
0
0
1
1
OUT
FO0
output pin. Table 4 shows the selection bits for
0
1
0
1
OUT
X1
X2
FIGURE 8. DIAGRAM OF ATR
output will now be pulsed each time an
C
C
X1
X2
Alarm output (F
OUTPUT FREQUENCY
32.768kHz
4096Hz
OSCILLATOR
1Hz
CRYSTAL
OUT
disabled)
August 18, 2008
FN6370.3