X9C303V8T1 Intersil, X9C303V8T1 Datasheet - Page 2

• Manufacturer Part Number: X9C303V8T1
• Description: IC XDCP 100-TAP 32K EE 8-TSSOP
• Manufacturer: Intersil
• Series: XDCP™r

Specifications of X9C303V8T1

• Taps: 100
• Resistance (ohms): 32K
• Number Of Circuits: 1
• Temperature Coefficient: 300 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: Up/Down (3-Wire)
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Package / Case: 8-TSSOP
• Resistance In Ohms: 32K
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Ordering Information
Pin Descriptions
V
The high (V
equivalent to the fixed terminals of a mechanical
potentiometer. The minimum voltage is –5V and the
maximum is +5V. It should be noted that the terminology of
V
relation to wiper movement direction selected by the U/D
input and not the voltage potential on the terminal.
V
V
of a mechanical potentiometer. The position of the wiper
within the array is determined by the control inputs. The
wiper terminal series resistance is typically 40Ω.
Up/Down (U/D)
The U/D input controls the direction of the wiper movement
and whether the counter is incremented or decremented.
Increment (INC)
The INC input is negative-edge triggered. Toggling INC will
move the wiper and either increment or decrement the counter
in the direction indicated by the logic level on the U/D input.
Chip Select (CS)
The device is selected when the CS input is LOW. The current
counter value is stored in nonvolatile memory when CS is
X9C303P
X9C303PI
X9C303PIZ (Notes 1, 2)
X9C303PZ (Notes 1, 2)
X9C303S8*
X9C303S8I*
X9C303S8IZ* (Note 1)
X9C303S8Z* (Note 1)
X9C303V8*
X9C303V8I*
X9C303V8IZ* (Note 1)
X9C303V8Z* (Note 1)
X9C303S8I-2.7
X9C303S8IZ-2.7 (Note 1) X9C303S ZG
*Add “T1” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
**Add “T2” suffix for tape and reel. Please refer to TB347 for details on reel specifications.
NOTES:
L
W
1. These Intersil Pb-free plastic packaged products employ special Pb-free material sets, molding compounds/die attach materials, and 100%
2. Pb-free PDIPs can be used for through hole wave solder processing only. They are not intended for use in Reflow solder processing applications.
H
W
and V
and V
is the wiper terminal, equivalent to the movable terminal
matte tin plate plus anneal (e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations).
Intersil Pb-free products are MSL classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC
J STD-020.
NUMBER
H
PART
L
,
,
references the relative position of the terminal in
H
**
**
) and low (V
X9C303P
X9C303P I
X9C303P ZI
X9C303P Z
X9C303S
X9C303S I
X9C303S ZI
X9C303S Z
9C303
C303 I
C303 IZ
9C303 Z
X9C303S G
L
) terminals of the device are
2
MARKING
PART
TEMP. RANGE
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
0 to +70
0 to +70
0 to +70
0 to +70
0 to +70
0 to +70
X9C303
(°C)
returned HIGH while the INC input is also HIGH. After the store
operation is complete, the device will be placed in the low
power standby mode until the device is selected once again.
Pinouts
8 Ld PDIP
8 Ld PDIP
8 Ld PDIP (300 mil) (Pb-free)
8 Ld PDIP (300 mil) (Pb-free)
8 Ld SOIC (150 mil)
8 Ld SOIC (150 mil)
8 Ld SOIC (150 mil) (Pb-free)
8 Ld SOIC (150 mil) (Pb-free)
8 Ld TSSOP (4.4mm)
8 Ld TSSOP (4.4mm)
8 Ld TSSOP (4.4mm) (Pb-free)
8 Ld TSSOP (4.4mm) (Pb-free)
8 Ld SOIC (150 mil)
8 Ld SOIC (150 mil) (Pb-free)
V
INC
U/D
INC
U/D
V
CS
CC
V
SS
H
(8 LD SOIC, 8 LD PDIP)
PACKAGE
1
2
3
4
1
2
3
4
(8 LD TSSOP)
TOP VIEW
TOP VIEW
X9C303
X9C303
X9C303
X9C303
8
7
6
5
8
7
6
5
V
CS
V
V
MDP0031
MDP0031
MDP0031
MDP0031
MDP0027
MDP0027
MDP0027
MDP0027
M8.173
M8.173
M8.173
M8.173
MDP0027
MDP0027
V
V
V
V
CC
L
W
L
W
SS
H
DWG. #
January 30, 2009
PKG.
FN8223.2