X9110TV14IZ Intersil, X9110TV14IZ Datasheet
X9110TV14IZ
Specifications of X9110TV14IZ
Available stocks
Related parts for X9110TV14IZ
X9110TV14IZ Summary of contents
Page 1
... DATA REGISTERS (DR0-DR3) CONTROL CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 1-888-468-3774 XDCP is a trademark of Intersil Americas INC. Copyright Intersil Americas Inc. 2005, 2008. All Rights Reserved FN8158.3 : 2.7V to 5.5V Operation CC X9110 14 LD TSSOP TOP VIEW V+ 14 ...
Page 2
... X9110TV Z F X9110TV14I-2.7 X9110TV G X9110TV14IZ-2.7* (Note) X9110TV Z G *Please refer to TB347 for details on reel specifications. NOTE: These Intersil Pb-free plastic packaged products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate PLUS ANNEAL - e3 termination finish, which is RoHS compliant and compatible with both SnPb and Pb-free soldering operations. ...
Page 3
Circuit Level Applications • Vary the gain of a voltage amplifier • Provide programmable dc reference voltages for comparators and detectors • Control the volume in audio circuits • Trim out the offset voltage error in a voltage amplifier circuit ...
Page 4
SERIAL DATA PATH FROM INTERFACE CIRCUITRY REGISTER 0 (DR0) REGISTER 2 (DR2) If WCR = 000[HEX] then WCR = 3FF[HEX] then FIGURE 1. DETAILED POTENTIOMETER BLOCK DIAGRAM Potentiometer Pins ...
Page 5
Data Registers via the XFR Data Register; ( loaded with the contents of its data register zero (DR0) upon power-up. The Wiper Counter Register is ...
Page 6
TABLE 4. IDENTIFICATION BYTE FORMAT DEVICE TYPE IDENTIFIER ID3 ID2 0 1 (MSB) TABLE 5. INSTRUCTION BYTE FORMAT INSTRUCTION OPCODE I2 I1 (MSB) Device Instructions Identification Byte (ID and A) The first byte sent to the X9110 from the host, ...
Page 7
Write in Process (WIP bit) The contents of the Data Registers are saved to nonvolatile memory when the CS pin goes from LOW to HIGH after a complete write sequence is received by the device. The progress of this internal ...
Page 8
INSTRUCTION R/W Read Wiper Counter 1 Register Write Wiper Counter 0 Register Read Data Register 1 Write Data Register 0 XFR Data Register to 1 Wiper Counter Register XFR Wiper Counter 0 Register to Data Register Read Status (WIP bit) ...
Page 9
Write Data Register (DR) Device Type Device Instruction Identifier Addresses Opcode CS Falling Edge Transfer Data Register (DR) to ...
Page 10
... Thermal Resistance (Typical, Note 4) 14 Lead TSSOP . . . . . . . . . . . . . . . . . . . . . . . . . . . . Temperature Under Bias . . . . . . . . . . . . . . . . . . . . .-65°C to +135°C Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65°C to +150°C Pb-Free Reflow Profile .see link below http://www.intersil.com/pbfree/Pb-FreeReflow.asp Recommended Operating Conditions Temperature Range Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to +70°C Industrial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-40°C to +85°C Supply Voltage (V X9110 ± ...
Page 11
D.C. Operating Specifications Over the recommended operating conditions unless otherwise specified SYMBOL PARAMETER I V Supply Current CC1 CC (active Supply Current CC2 CC (nonvolatile write Current (standby Input Leakage Current LI I ...
Page 12
Equivalent A.C. Load Circuit 5V 1462Ω SO pin 2714Ω 100pF AC Timing SYMBOL f SSI/SPI Clock Frequency SCK t SSI/SPI Clock Cycle Time CYC t SSI/SPI Clock High Time WH t SSI/SPI Clock Low Time WL t Lead Time LEAD ...
Page 13
High-Voltage Write Cycle Timing SYMBOL t High-Voltage Write Cycle Time (store instructions) WR XDCP Timing SYMBOL t Wiper Response Time After the Third (last) Power Supply is Stable WRPO t Wiper Response Time After Instruction Issued (all load instructions) WRL ...
Page 14
Timing Diagrams Input Timing CS t LEAD SCK MSB SI HIGH IMPEDANCE SO Output Timing CS SCK t V MSB SO ADDR SI Hold Timing CS SCK HOLD 14 X9110 t CYC ...
Page 15
XDCP Timing (For All Load Instructions) CS SCK MSB HIGH IMPEDANCE SO Write Protect And Device Address Pins Timing Applications information Basic Configurations Of Electronic Potentiometers V R Three terminal Potentiometer; Variable voltage ...
Page 16
Application Circuits NONINVERTING AMPLIFIER – (1 OFFSET VOLTAGE ADJUSTMENT 100kΩ – + TL072 10kΩ 10kΩ 10kΩ +12V -12V 16 X9110 V V ...
Page 17
Application Circuits (continued) ATTENUATOR – -1/2 ≤ G ≤ +1/2 INVERTING AMPLIFIER ...
Page 18
... Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use ...