X9314WSIT2 Intersil, X9314WSIT2 Datasheet - Page 2

• Manufacturer Part Number: X9314WSIT2
• Description: IC XDCP SGL 32-TAP 10K 8-SOIC
• Manufacturer: Intersil
• Series: XDCP™r

Specifications of X9314WSIT2

• Taps: 32
• Resistance (ohms): 10K
• Number Of Circuits: 1
• Temperature Coefficient: 300 ppm/°C Typical
• Memory Type: Non-Volatile
• Interface: Up/Down (3-Wire)
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Resistance In Ohms: 10K
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

Ordering Information
*Add "T1" suffix for tape and reel.
NOTE: Intersil Pb-free plus anneal products employ special Pb-free material sets; molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with both SnPb and Pb-free soldering operations. Intersil Pb-free products are MSL
classified at Pb-free peak reflow temperatures that meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
Pin Descriptions
V
The high (V
are equivalent to the fixed terminals of a mechanical
potentiometer. The minimum voltage is –5V and the
maximum is +5V. It should be noted that the terminology of
V
terminal in relation to wiper movement direction selected by
the U/D input and not the voltage potential on the terminal.
V
V
terminal of a mechanical potentiometer. The position of the
wiper within the array is determined by the control inputs.
The wiper terminal series resistance is typically 40Ω.
Up/Down (U/D)
The U/D input controls the direction of the wiper movement
and whether the counter is incremented or decremented.
Increment (INC)
The INC input is negative-edge triggered. Toggling INC will
move the wiper and either increment or decrement the
counter in the direction indicated by the logic level on the
U/D input.
Chip Select (CS)
The device is selected when the CS input is LOW. The
current counter value is stored in nonvolatile memory when
CS is returned HIGH while the INC input is also HIGH. After
the store operation is complete the X9314 will be placed in
the low power standby mode until the device is selected
once again.
X9314WMI*
X9314WP
X9314WPI
X9314WS*
X9314WSI*
X9314WSIZ (Note)
X9314WSZ* (Note)
X9314WMI-3*
X9314WMIZ-3* (Note)
X9314WS-3*
X9314WSZ-3* (Note)
L
W
H
W
/R
/R
/R
/R
L
W
H
W
and V
PART NUMBER
and V
is the wiper terminal, equivalent to the movable
H
H
/R
/R
L
H
/R
H
) and low (V
references the relative position of the
L
14WI
X9314WP
X9314WP I
X9314W
X9314W I
X9314W ZI
X9314W Z
AAY
DEX
X9314W D
X9314W ZD
L
PART MARKING
2
/R
L
) terminals of the X9314
V
CC
5 ±10%
3 to 5.5
RANGE
(V)
X9314
R
TOTAL
(kΩ)
10
Pin Configuration
Pin Names
TEMP RANGE
SYMBOL
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
-40 to +85
V
0 to +70
0 to +70
0 to +70
0 to +70
0 to +70
V
V
V
V
V
W
V
V
W
U/D
INC
H
CS
(°C)
V
L
H
H
CC
SS
/R
/R
/R
/R
L
/R
INC
U/D
/R
V
V
/R
SS
SS
W
H
H
W
L
H
L
1
2
3
4
8 LD PDIP/SOIC
1
2
3
4
8 Ld MSOP
8 Ld PDIP
8 Ld PDIP
8 Ld SOIC
8 Ld SOIC
8 Ld SOIC (Pb-free) M8.15
8 Ld SOIC (Pb-free) M8.15
8 Ld MSOP
8 Ld MSOP (Pb-free) M8.118
8 Ld SOIC
8 Ld SOIC (Pb-free) M8.15
8 LD MSOP
X9314
X9314
PACKAGE
8
7
6
5
8
7
6
5
Chip Select Input
Increment Input
DESCRIPTION
Wiper Terminal
Supply Voltage
Up/Down Input
High Terminal
Low Terminal
V
CS
V
V
Ground
U/D
INC
V
CS
CC
L
W
CC
/R
/R
M8.118
MDP0031
MDP0031
M8.15
M8.15
M8.118
M8.15
L
W
September 5, 2006
DWG. #
PKG.
FN8178.2